manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual, Page: 175 / 450

Share
Download
BERTHOLD TECHNOLOGIES LB 480 User Manual Download Page 175

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

2 – 175

Volume 2

2 Installation

2

2.2

Source Detector Arrangements

BERTHOLD TECHNOLOGIES offers a large number of options for 
your particular measurement setup. The schematic drawings below 
show examples of different arrangements which will guide you to 
the respective installation instructions. Since other arrangements 
are also possible, the installation of the detector side and the 
source side will be explained separately. For this reason, you may 
find the installation instructions for the detector in another setup 
example than the instructions for the source.

Point source with shielding 45° and 

rod detector

Point source with shielding 45° cas-

caded and Tower-Sens

Rod source with shielding and point 

detector NaI 50/50 or Super-Sens

Rod source with shielding and rod 

detector

Rod source with shielding cascaded 

and rod detector cascaded or 

Tower-Sens

Point source with shielding LB744X 

and point detector NaI 50/50 or 

Super-Sens

Rod source in dip tube and rod detec-

tor

Rod source in dip tube and point 

detector NaI 50/50 or Super-Sens

Point source with shielding LB744X 

and point detector NaI 50/50 or 

Super-Sens

The limit switch differs from the continuous level measurements in that the 
exceeding of the level is specifically detected at a certain position and 
reported. This position is physically fixed by the mechanical arrangement and 
is highly reliable to prevent over- and underfilling.

Point source/

shielding 45°

page 2-191

Rod detector

page 2-180

Point source/

shielding 45°

page 2-191

Tower SENS

page 2-183

Rod source

page 2-198

Crystal SENS

page 2-183

Co

nt

in

uo

us

 lev

e

l 

m

eas

ur

emen

t

Rod source

page 2-198

Rod detector

page 2-180

Rod source

page 2-203

Rod detector

page 2-180

Tower SENS

page 2-183

Point source

with LB 744X

page 2-214

Crystal SENS

page 2-183

Flange shielding for

safety position

Rod detector

page 2-180

Rod source

page 2-205

Rod source

page 2-205

Flange shielding for

safety position

Crystal SENS

page 2-183

Point source

with LB744X

page 2-214

Crystal SENS

page 2-183

Limit swit

ch

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments