manualshive.com logo in svg

BERTHOLD TECHNOLOGIES LB 480, User Manual

The BERTHOLD TECHNOLOGIES LB 480 is a cutting-edge laboratory device that is essential for accurate measurements. To ensure proper usage, don't forget to download the user manual for free at manualshive.com. This manual provides detailed instructions on how to operate and maintain this advanced technology.

Share
Download
background image

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

3 – 347

Volume 3

Menu Structure

3

In absorption measurements with point source and point detector:

The path between the maximum level (100%) and the dip tube in 
which the source is installed.

However, only the section in the room filled with gas.

5 Setup Gas Density

Visible only if 

Compensation Mode

 is set to 

MANUAL GDA

.

Enter the gas pressure in kg/m

3

 which is present during cali-

bration. 

Use this parameter only if the gas density during calibration is dif-
ferent from the gas density under operating conditions.

Using the gas density, a compensated count rate is then calculated 
from the count rate in 

Lower Cal Pt-Empty

 (

Device Config

 

 

Setup

 

 

Cal Parameter

 

 

Cal Points

 

 

Cal Rate at OP

), which 

you can read off under 

Op Lower Point

.

Prerequisite for the proper correction are correct entries in the fol-
lowing menu items:

• Setup Gas Density

• Op  Gas  Density

• Measuring  Path

• Nuclide

100%

0%

Point detector

Product

Gas

Gas me

asuring

 path

Me

as

urin

g Path

Summary of Contents for LB 480



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LB 480

Magnetic Instrumentation 2130 Instruction Manual preview
2130
Brand: Magnetic Instrumentation Pages: 63
Parr Instrument Company 6300 Operating Instructions Manual preview
6300
Brand: Parr Instrument Company Pages: 130
jenway 6300 Operating Manual preview
6300
Brand: jenway Pages: 17
UEi C257 Instruction Manual preview
C257
Brand: UEi Pages: 20
Hach A1000 Basic User Manual preview
A1000
Brand: Hach Pages: 138
dbx DDP Manual preview
DDP
Brand: dbx Pages: 2
Kamstrup MULTICAL 62 Technical Description preview
MULTICAL 62
Brand: Kamstrup Pages: 100
Kamstrup MULTICAL 41 Installation And User Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 41 Installation Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 12
Kamstrup flowIQ 3100 Technical Description preview
flowIQ 3100
Brand: Kamstrup Pages: 60
Kamstrup MULTICAL 403 Technical Description preview
MULTICAL 403
Brand: Kamstrup Pages: 136
Kamstrup ULTRAFLOW 54 Installation Manual preview
ULTRAFLOW 54
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 603 Technical Description preview
MULTICAL 603
Brand: Kamstrup Pages: 155
PASCO PS-3215 Battery Replacement preview
PS-3215
Brand: PASCO Pages: 3
insize PLUS 3631 Series Operation Manual preview
PLUS 3631 Series
Brand: insize Pages: 1
Datakom DKM-260 User Manual preview
DKM-260
Brand: Datakom Pages: 28
Eno Scientific Well Watch 700 User Manual preview
Well Watch 700
Brand: Eno Scientific Pages: 47
GAGEMAKER BXG-1000 Operation Manual preview
BXG-1000
Brand: GAGEMAKER Pages: 36

Brands by name

Popular brands

Load more brands