Berner 201167, Original Instructions Manual

Page: 17 / 249

English | 17
1 609 92A 1D1 • 12.8.15
forced in the direction opposite of the accesso-
ry’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse
and/or incorrect operating procedures or condi-
tions and can be avoided by taking proper pre-
cautions as given below.
 Maintain a firm grip on the power tool and po-
sition your body and arm to allow you to resist
kickback forces. Always use auxiliary handle,
if provided, for maximum control over kick-
back or torque reaction during start-up. The
operator can control torque reactions or kick-
back forces, if proper precautions are taken.

Never place your hand near the rotating acces-
sory. Accessory may kickback over your hand.

Do not position your body in the area where
power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.

Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
 Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create fre-
quent kickback and loss of control.
Safety warnings specific for Grinding and Abra-
sive Cutting-Off operations
 Use only wheel types that are recommended
for your power tool and the specific guard de-
signed for the selected wheel. Wheels for
which the power tool was not designed cannot
be adequately guarded and are unsafe.
 The grinding surface of the centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel that
projects through the plane of the guard lip can-
not be adequately protected.
 The guard must be securely attached to the
power tool and positioned for maximum safe-
ty, so the least amount of wheel is exposed to-
wards the operator. The guard helps to protect
operator from broken wheel fragments, acciden-
tal contact with wheel and sparks that could ig-
nite clothing.
 Wheels must be used only for recommended
applications. For example: do not grind with
the side of the cut-off wheel. Abrasive cut-off
wheels are intended for peripheral grinding; side
forces applied to these wheels may cause them
to shatter.
 Always use undamaged wheel flanges that are
of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel flanges.
 Do not use worn down reinforced wheels from
larger power tools. Wheels intended for larger
power tools are not suitable for the higher speed
of a smaller tool and may burst.
Additional safety warnings specific for abrasive
cutting off operations
 Do not “jam” the cut-off wheel or apply exces-
sive pressure. Do not attempt to make an ex-
cessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twist-
ing or binding of the wheel in the cut and the
possibility of kickback or wheel breakage.
 Do not position your body in line with and be-
hind the rotating wheel. When the wheel, at the
point of operation, is moving away from your
body, the possible kickback may propel the
spinning wheel and the power tool directly at
you.
 When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never at-
tempt to remove the cut-off wheel from the cut
while the wheel is in motion otherwise kick-
back may occur. Investigate and take corrective
action to eliminate the cause of wheel binding.
 Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
 Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
 Use extra caution when making a “pocket cut”
into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kick-
back.
Safety warnings specific for sanding operations
 Do not use excessively oversized sanding disc
paper. Follow manufacturers recommenda-
tions, when selecting sanding paper. Larger
sanding paper extending beyond the sanding
pad presents a laceration hazard and may cause
snagging, tearing of the disc, or kickback.
OBJ_BUCH-1019-004.book Page 17 Wednesday, August 12, 2015 4:12 PM