Belanger H2AIR ARCH Owner'S Manual Download Page 41 | Manualshive

Page: 41 / 72

background image

H2AIR

®

ARCH

1MANUL958

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

37

Initial Startup Procedures

Install Spray Nozzles & Verify Proper Function of Top Assembly and Airis®

10) The H2AIR® Arch has several functions that must be activated as a vehicle approaches the arch.

Program the H2AIR® Arch so that when the front bumper of a vehicle is about 2 feet from the
H2AIR® Arch the following functions start simultaneously:



Turn on Water for the Top and Leg Manifolds



Turn on Air Cannon

™ DryLite™ Dryers



Activate the Airis® 4-way valve to open the Airis® Assemblies



Turn on the LED Lights in the Leg Assemblies, Top Manifolds and Dryer Housings

11) Run a test wash on a vehicle to confirm the H2AIR® Arch is operating as desired and make

adjustments as necessary.

Note:

It is recommeded that the Airis® Assemblies open as quick as possible after the dryers turn on.

Use the Flow Control on the Extend Ports of the Airis® Cylinders to increase the speed at
which the Airis® Assemblies open.

«
...
39
40
41
42
43
...
»

Summary of Contents for H2AIR ARCH









































































Reviews:

No comments

Related manuals for H2AIR ARCH

Brand: NEC Pages: 44

Brand: Haki Pages: 24

Brand: Dakota Digital Pages: 5

Brand: Nitecore Pages: 4

Brand: WalkMed Pages: 2

Brand: Walinga Pages: 20

Sonorex Super RK 31

Brand: BANDELIN Pages: 21

BTL7-A/E501-M Series

Brand: Balluff Pages: 194

Brand: B.Pro Pages: 48

Brand: ABB Pages: 16

Brand: ABB Pages: 2

i-limb access hand

Brand: Össur Pages: 246

PROPRIO FOOT PSX01

Brand: Össur Pages: 374

Brand: Kelvin Pages: 30

Brand: PARAMOUNT BED Pages: 120

Brand: Hameg Pages: 39

Brand: Teac Pages: 1

Brand: Garelick Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands