Belanger H2AIR ARCH Owner'S Manual Download Page 5

Page: 5 / 72

H2AIR

ARCH

1MANUL958

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Table of Contents

Belanger Incorporated® Limited Warranty ....................................................... 3

Operational Warning ........................................................................................... 4

Introduction ......................................................................................................... 5

Important Safety Information ..................................................................................................... 5

Safety Symbols and Signal Words ............................................................................................ 5

IMPORTANT Safety Information

– MUST READ ...................................................................... 6

Overview .................................................................................................................................... 8

Before You Get Started ............................................................................................................. 9

Available Leg Manifold Cover Choices .................................................................................... 10

Specifications .................................................................................................... 11

Requirements .......................................................................................................................... 11

Physical ............................................................................................................................................ 11

Utility ................................................................................................................................................. 11

Electrical Specifications for Motors: .................................................................................................. 11

Dimensions .............................................................................................................................. 12

Installation ......................................................................................................... 13

Inspection Shipment & Install Airis® Assemblies

onto Air Cannon™ Dryer Housings ........... 13

Prepare to Assemble Arch ....................................................................................................... 18

Attach Leg Assemblies to Head Beam Assembly ................................................................... 19

Tunnel Placement .................................................................................................................... 21

Connect Water Hoses from Leg Assemblies to Water Manifold ............................................. 25

Route LED Cables from Leg Assemblies to Electrical Box ..................................................... 26

Utilities ............................................................................................................... 27

Electrical Connection: Main Power to

DryLite™ Dryer Motors ................................................ 27

Electrical Connection: H2Air® Air Panel to Controller ............................................................. 28

Electrical Connection: Airis® Air Panel to Controller ............................................................... 28

Electrical Connections: Overview for LEDs ............................................................................. 29

Electrical Connections: Main Power for DryLite

™ Dryers & Top Manifold LEDs .................... 29

Electrical Connections: Main Power for Leg Assembly LEDs ................................................. 30

Air Connections: Air Panel to H2AIR® Top Flip Cylinder ........................................................ 31

Air Connections: Air Panel to Airis® Assemblies .................................................................... 32

Water Connection: Main Feed to H2AIR® Water Manifold ..................................................... 33

Initial Startup Procedures ................................................................................. 34

Install Spray Nozzles & Verify Proper Function of Top Assembly and Airis® ......................... 34

Maintenance ...................................................................................................... 38

Routine Procedures ................................................................................................................. 38

H2AIR® Arch (Daily) ......................................................................................................................... 38

H2AIR® Arch (Monthly) .................................................................................................................... 38

Summary of Contents for H2AIR ARCH









































































Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands

Belanger H2AIR ARCH, Owner'S Manual

Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands