Belanger H2AIR ARCH Owner'S Manual Download Page 35

Page: 35 / 72

H2AIR

ARCH

1MANUL958

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Utilities

Air Connections: Air Panel to H2AIR® Top Flip Cylinder

1) Run a field supplied

1/4” poly-flow airline from the Main Air Supply to the Main Air Connection on

the Air Panel. See the image below.

2) Run a field supplied

1/4” poly-flow airline from the extend regulator on the Air Panel to the extend

port on the Top Flip Cylinder. See the images above and below.

3) Run a field supplied

1/4” poly-flow airline from the retract regulator on the Air Panel to the retract

port on the Top Flip Cylinder. See the images above.

Retract Regulator Connection

1/4” Poly-Flow Tube to the Retract

Port on the Cylinder

120 VAC Output from

the Site Controller

Main Air Connection

1/4” Poly-Flow Tube

Extend Regulator Connection

1/4” Poly-Flow Tube to the

Extend Port on the Cylinder

4-Way Air Valve

Field Supplied
1/4" Poly Flow Tube
Route as necessary

Field Supplied 1/4" Poly

Flow Tube from the

Main Pneumatic Source

@100 psi Air Flow Min.

Extend Port

Air Panel

Retract Port

Extend Port

Retract Port

Each port on the Cylinder
has a flow control valve to
adjust the cylinder actuation
speed.

The Cover was removed
from the Top Flip to see the
ports on the Cylinder.

Notes:

Summary of Contents for H2AIR ARCH









































































Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands

Belanger H2AIR ARCH, Owner'S Manual

Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands