Belanger H2AIR ARCH Owner'S Manual Download Page 33 | Manualshive

Page: 33 / 72

background image

H2AIR

®

ARCH

1MANUL958

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

29

Utilities

Electrical Connections: Overview for LEDs

The H2AIR® Arch has RGB LED-illuminated

DryLite™ Air Cannon™ Dryer Nozzles, Top Manifold

Assemblies and Leg Manifold Assemblies. The LED lights for the

DryLite™ Dryer Nozzles and the Top

Manifolds were prewired, at Belanger®, within the Electrical Box on the passenger side of the Top Flip
Weldment. Then during installation of the H2AIR® Arch the wires for the LED lights in the Leg Assemblies
were routed to the Electrical Box on the driver side of the Top Flip Weldment. At this time all of the LED
cables are ready to be wired to the Main Power.

Electrical Connections: Main Power for DryLite

™ Dryers & Top Manifold LEDs

1) Remove the cover on the Electrical Box on the passenger side of the Top Flip Weldment, shown

below.

CAUTION

It is recommended that a licensed electrician is contracted to perform all electrical installations.

2) Route two Main Power Lines, one for the Dryer Nozzles LEDs and one for the Top Manifold

LEDs, from the Controller to the top of the H2AIR® and through the Cord Grips in the Electrical
Box, shown above.

3) When everything is wired properly, close and seal the Electrical Box be cautious to not crimp

down on any of the wires.

4) Test to see if all the LEDs are functioning properly by using the Controller to turn on each of the

LEDs.

LED Wires for
Top Manifolds and
Dryer Nozzles

Electrical Box Cover

Cord Grips

Top Flip Weldment

«
...
31
32
33
34
35
...
»

Summary of Contents for H2AIR ARCH









































































Reviews:

No comments

Related manuals for H2AIR ARCH

Brand: Navman Pages: 17

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: A.MENARINI Pages: 2

Brand: XM Fitness Pages: 10

Brand: Parker Pages: 39

Brand: Patty-O-Matic Pages: 28

Brand: tayco Pages: 111

Brand: Jacobsen Pages: 20

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: Waters Pages: 250

Brand: Waters Pages: 141

REBOUND DUAL ST

Brand: Össur Pages: 104

Brand: Össur Pages: 130

Brand: Kanlux Pages: 4

Brand: VaBroom Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands