Belanger H2AIR ARCH Owner'S Manual Download Page 18

Page: 18 / 72

H2AIR

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL958

Installation

Install Airis® Assemblies onto Air

Cannon™ Dryer Housings

5) The Airis® Assemblies

will be mounted to the inlet of the Air Cannon™ Housing with the

Cylinder parallel with the outlet of the housing and the Cylinder Bumper facing down, refer to the
image below.

Note:

A clockwise (CW) Airis® is to be attached to a CW Air Cannon™ Blower Housing and a

counter-clockwise (CCW) Airis® is to be attached to a CCW Air Cannon™ Blower Housing.

Hold the Airis® over the top of the Inlet Cone and select the four holes that will be used to
mount the Airis® assembly.

Air Cannon™

Blower Housing

Air Cannon™ Outlet

DryLite™ Air Cannon™ with
Airis

CW Assembly Shown

Air Cannon™
Housing Inlet

Airis®

Cylinder for Airis®

Cylinder Bumper

Four (4) Holes to be used to
mount the Airis® Assembly

Airis® Assembly

Air Cannon™

Blower Housing

Inlet Cone

Summary of Contents for H2AIR ARCH









































































Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands

Belanger H2AIR ARCH, Owner'S Manual

Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands