Belanger H2AIR ARCH Owner'S Manual Download Page 32

Page: 32 / 72

H2AIR

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL958

Utilities

Electrical Connection: H2Air® Air Panel to Controller

1) Locate the Air Panel, see image below, that came with the H2AIR® Arch. Mount the Air Panel in

a dry location.

Note:

The 4-Way Air Valve requires a 120VAC program function from the site controller.

2) Supply 120 VAC to the 4-Way Air Valve on the Air Panel from the carwash controller unit.

Electrical Connection: Airis® Air Panel to Controller

1) Locate the Air Panel (111389) in the Airis®

Air Cannon™ Dual Kit, see image below. Mount the

Air Panel in a dry location.

2) Wire the 4-Way Air Valve to the 120 VAC output on the carwash controller unit.

120 VAC in

It is recommended that a licensed electrician is contracted to perform

all electrical installations. All utilities MUST be installed in

accordance with all local and national codes.

Air Panel: 111389

120 VAC

4-Way Air Valve

Retract Regulator Connection

1/4” Poly-Flow Tube to the Retract

Port on the Cylinder

120 VAC Output from

the Site Controller

Main Air Connection

1/4” Poly-Flow Tube

Extend Regulator Connection

1/4” Poly-Flow Tube to the

Extend Port on the Cylinder

4-Way Air Valve

It is recommended that a licensed electrician is

contracted to perform all electrical installations. All

utilities MUST be installed in accordance with all

local and national codes.

Summary of Contents for H2AIR ARCH









































































Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands

Belanger H2AIR ARCH, Owner'S Manual

Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands