Belanger H2AIR ARCH Owner'S Manual Download Page 30

Page: 30 / 72

H2AIR

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL958

Installation

Route LED Cables from Leg Assemblies to Electrical Box

1) Route the LED Cable from the driver side Leg Assembly to the Electrical Box mounted on the

driver side of the Top Flip Weldment, as shown in the images below.

2) Route the LED Cable from the passenger side Leg Assembly to the same Electrical Box, as

shown above.

3) These cables will be connected to the main power in the Utilities section of this manual.

LED Cable for

DS Leg Asy

LED Cable

for PS Leg

Asy

Step 2

Route the LED Cable
from the PS Leg Asy to

the Electrical Box on the
driver side of the Top Flip

Weldment.

Electrical Box

for Leg Asy.

LEDs

Step 1

Route the LED Cable

from the DS Leg Asy to
the Electrical Box on the

driver side of the Top Flip
Weldment.

Summary of Contents for H2AIR ARCH









































































Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands

Belanger H2AIR ARCH, Owner'S Manual

Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands