Belanger H2AIR ARCH Owner'S Manual Download Page 21

Page: 21 / 72

H2AIR

ARCH

1MANUL958

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Install Airis® Assemblies onto

Air Cannon™ Dryer Housings

13)

Thread the 3/8”-16 x 1” fasteners through the plastic housing and into the Airis® Support
Mounting Stud Assembly (111382) and tighten the four fasteners to hold the Airis® support
mounting studs in place.

14) Reinstall the Inlet Cone over the four threaded

mounting studs and reinstall four of the 5/16”-18 x

1” fasteners, lock washers and aluminum flat washers into the remaining Nut Retainers
(1RETNR650) and tighten down the Inlet Cone (1IMPLR-CO500).

15) Install the Airis® onto the four threaded studs making sure that the orientation is correct, as

shown in the images below.

16) In the Airis®

accessory box locate four 3/8”-16 Nyloc nuts (1NUT-LC215), install and tighten them

onto the threaded mounting studs to secure the Airis®

onto the Air Cannon™ Housing, see

images above.

17) Repeat Steps 6-16

for the other Air Cannon™.

1NUT-LC215 (4)

Airis® Assembly

11382 (4): Threaded

Mounting Studs

Inlet Cone

Nut Retainer (4)

5/16”-18x1”
Fastener & Washers

Summary of Contents for H2AIR ARCH









































































Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands

Belanger H2AIR ARCH, Owner'S Manual

Search results

Summary of Contents for H2AIR ARCH

Reviews:

Related manuals for H2AIR ARCH

Brands by name

Popular brands