BCDVideo BCD221 User Manual Download

Page: 68 / 157

Connect the power cable

10. Install a storage controller

11. Connect the data cables from the drive backplane to the controller

12. Install drives

or drive blanks.

The installation is complete.

Installing airflow labels

When an Express Bay drive cage is installed, airflow labels might be required:

Prerequisites

Before installing this option, be sure that you have the following:

• The components included with the hardware option kit

Procedure

• If an eight-bay SFF drive cage is installed in box 1, then airflow labels are not required.
• If a blank is installed in box 1, replace it with the blank that comes with the kit.

• If a Universal Media Bay is installed in box 1, do one of the following:

Installing airflow labels

Summary of Contents for BCD221






























































































































































Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands

BCDVideo BCD221, User Manual

Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands