BCDVideo BCD221 User Manual Download Page 76

Page: 76 / 157

Remove all riser cages.

Connect the power cable to the drive backplane power connector on the system board.

If connecting the data cable to the system board or a controller, connect the data cable.

Prepare the drive cage for installation by lifting the latches on the drive cage.

10.

Install the drive cage:

CAUTION:

Do not drop the drive cage on the system board. Dropping the drive cage on the system board
might damage the system or components. Remove all drives and use two hands when installing or
removing the drive cage.

Locate the alignment pins on the rear of the drive cage.

Align the pin on the rear left of the drive cage to the server and then insert the pin.

Gently lower the opposite side of the drive cage.

Pull the plunger pin on the rear right of the drive cage and then lower the drive cage until the plunger
pin engages.

Hardware options installation

Summary of Contents for BCD221






























































































































































Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands

BCDVideo BCD221, User Manual

Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands