manualshive.com logo in svg

BCDVideo BCD221, User Manual, Page: 135 / 157

Share
Download
BCDVideo BCD221 User Manual Download Page 135

For more information, see the following website: 

http://www.hpe.com/info/resttool

.

iLO Amplifier Pack

The iLO Amplifier Pack is an advanced server inventory and firmware and driver update solution that enables
rapid discovery, detailed inventory reporting, and firmware and driver updates by leveraging iLO advanced
functionality. The iLO Amplifier Pack performs rapid server discovery and inventory for thousands of
supported servers for the purpose of updating firmware and drivers at scale.

For more information about iLO Amplifier Pack, see the iLO Amplifier Pack user guide on the Hewlett Packard
Enterprise website.

Intelligent Provisioning

Intelligent Provisioning is a single-server deployment tool embedded in servers, Apollo systems, and

 

HPE 

Synergy compute modules. Intelligent Provisioning simplifies server setup, providing a reliable and

 

consistent 

way to deploy servers.

Intelligent Provisioning prepares the system for installing original, licensed vendor media and Hewlett Packard

 

Enterprise-branded versions of OS software. Intelligent Provisioning also prepares the system to integrate

 

optimized server support software from the Service Pack for (SPP). SPP is a comprehensive

 

systems 

software and firmware solution for

 

servers, server blades, their enclosures, and HPE

 

Synergy compute 

modules. These components are preloaded with a basic set of firmware and OS

 

components that are installed 

along with Intelligent Provisioning.

After the server is running, you can update the firmware to install additional components. You can also update

 

any components that have been outdated since the server was manufactured.

In addition to accessing Intelligent Provisioning by pressing F10 from the POST screen, you can also access

 

Intelligent Provisioning from the iLO web browser user interface using Always On. You can access Always On

 

without having to reboot your server.

Intelligent Provisioning operation

Intelligent Provisioning includes the following components:

• Critical boot drivers
• Active Health System (AHS)
• Erase Utility
• Deployment Settings

IMPORTANT:

• Although your server is pre-loaded with firmware and drivers, you should update the firmware upon

 

initial setup to ensure you have the latest versions. Also, downloading and updating the latest

 

version of Intelligent Provisioning ensures the latest supported features are available.

• For servers, firmware is updated using the Intelligent Provisioning Firmware Update utility.
• Do not update firmware if the version you are currently running is required for compatibility. 

NOTE:

Intelligent Provisioning does not function within multihomed configurations. A multihomed host is one
that is connected to two or more networks or has two or more IP addresses.

Intelligent Provisioning provides installation help for the following operating systems:

• Microsoft Windows Server
• Red Hat Enterprise Linux

iLO Amplifier Pack

135

Summary of Contents for BCD221






























































































































































Reviews:

No comments