manualshive.com logo in svg

BCDVideo BCD221, User Manual, Page: 79 / 157

Share
Download
BCDVideo BCD221 User Manual Download Page 79

8.

Cable the drive backplane

.

9.

Install drives or drive blanks

.

10. Install the access panel

.

11.

Slide the server into the rack.

12.

Connect each power cord to the server.

13.

Connect each power cord to the power source.

14. Power up the server

.

The installation is complete.

Installing a rear 2SFF SAS/SATA drive cage over the power supplies

Prerequisites

Before installing this option, be sure that you have the following:

• T-10 Torx screwdriver
• The components included with the hardware option kit
• The front bays are fully populated with 12 LFF or 24 SFF drives
• High performance fans are installed in all fan bays

Procedure

1.

Power down the server

.

2.

Remove all power:

a.

Disconnect each power cord from the power source.

b.

Disconnect each power cord from the server.

3.

Do one of the following:

•

Extend the server from the rack

.

•

Remove the server from the rack 

.

4.

Remove the access panel

.

5.

Do one of the following:
If installed, remove the secondary riser cage.

Installing a rear 2SFF SAS/SATA drive cage over the power supplies

79

Summary of Contents for BCD221






























































































































































Reviews:

No comments