manualshive.com logo in svg

BCDVideo BCD221, User Manual, Page: 67 / 157

Share
Download
BCDVideo BCD221 User Manual Download Page 67

11. Connect the data cables from the drive backplane to the NVMe riser

.

12. Install drives

 or drive blanks.

The installation is complete.

Installing a front 6SFF SAS/SATA + 2NVMe Premium drive cage

The drive cage can be installed in any box. This procedure covers installing the drive cage in box 1.

Prerequisites

A storage controller and high-performance fans are required when installing this drive cage.

Procedure

1.

Observe the following alerts.

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system
components to cool before touching them.

CAUTION:

To prevent damage to electrical components, properly ground the server before beginning any
installation procedure. Improper grounding can cause ESD.

2.

Power down the server 

.

3.

Do one of the following:

•

Extend the server from the rack

.

•

Remove the server from the rack 

.

4.

Remove the access panel

.

5.

Remove the air baffle

.

6.

Remove the fan cage

.

7.

Remove the blank. 

8.

Install the drive cage:

a.

If drive blanks are installed in the drive cage assembly, 

remove the drive blanks

. Retain the drive

blanks for use in empty drive bays.

b.

Install the drive cage.

Installing a front 6SFF SAS/SATA + 2NVMe Premium drive cage

67

Summary of Contents for BCD221






























































































































































Reviews:

No comments