BCDVideo BCD221 User Manual Download Page 37 | Manualshive

Page: 37 / 157

background image

Installing the fan cage

CAUTION:

Do not operate the server for long periods with the access panel open or removed. Operating the server
in this manner results in improper airflow and improper cooling that can lead to thermal damage.

IMPORTANT:

For optimum cooling, install fans in all primary fan locations.

Removing the air baffle or midplane drive cage

CAUTION:

Do not detach the cable that connects the battery pack to the cache module. Detaching the cable
causes any unsaved data in the cache module to be lost.

Installing the fan cage

37

«
...
35
36
37
38
39
...
»

Summary of Contents for BCD221






























































































































































Reviews:

No comments

Related manuals for BCD221

NECCare Platinum Express5800/A1160

Brand: NEC Pages: 4

NECCare Gold Express5800/320Fd

Brand: NEC Pages: 11

NEC Express5800/R120d-2E

Brand: NEC Pages: 39

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 244

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 191

UNIVERGE NEAX 2000 IPS

Brand: NEC Pages: 96

Brand: IBM Pages: 198

8841 - eServer xSeries 236

Brand: IBM Pages: 100

Brand: Sun Microsystems Pages: 128

D-811_002-NXS-SAG

Brand: NOMACHINE Pages: 19

Brand: SEH Pages: 5

Brand: Patton electronics Pages: 326

Snap! Server 4000

Brand: Quantum Pages: 8

H SERIES RS/6000

Brand: IBM Pages: 424

Brand: IBM Pages: 82

EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0

Brand: Edimax Pages: 118

FusionServer 2288 V5

Brand: xFusion Digital Technologies Pages: 86

Brand: Netstor Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands