BCDVideo BCD221 User Manual Download Page 35 | Manualshive

Page: 35 / 157

BCDVideo BCD221 User Manual Download Page 35

6.

Secure the cables to the cable management arm.

IMPORTANT:

When using cable management arm components, be sure to leave enough slack in each of the
cables to prevent damage to the cables when the server is extended from the rack.

7.

Connect the power cord to the AC power source.

WARNING:

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it. Pay

particular attention to the plug, electrical outlet, and the point where the cord extends from the
server.

Operations

35

«
...
33
34
35
36
37
...
»

Summary of Contents for BCD221






























































































































































Reviews:

No comments