BCDVideo BCD221 User Manual Download Page 44

Page: 44 / 157

Setup

HPE support services

Delivered by experienced, certified engineers, HPE support services help you keep your servers up and

running with support packages tailored specifically for systems. HPE support services let you

integrate both

hardware and software support into a single package. A number of service level options are

available to

meet your business and IT needs.

HPE support services offer upgraded service levels to expand the standard product warranty with easy-to-
buy, easy-to-use support packages that will help you make the most of your server investments. Some of the

HPE support services for hardware, software or both are:

• Foundation Care – Keep systems running.

◦ 6-Hour Call-to-Repair
◦ 4-Hour 24x7
◦ Next Business Day

• Proactive Care – Help prevent service incidents and get you to technical experts when there is one.

◦ 6-Hour Call-to-Repair
◦ 4-Hour 24x7
◦ Next Business Day

• Startup and implementation services for both hardware and software
• HPE Education Services – Help train your IT staff.

For more information on HPE support services, see the

Hewlett Packard Enterprise website

Setup overview

Procedure

Review the operational requirements for the server (

Operational requirements

on page 44).

Read the following safety notices, warnings, and cautions:

• Server warnings and cautions (

Server warnings and cautions

on page 46)

• Rack warnings (

Rack warnings

on page 47)

• Electrostatic discharge (

Electrostatic discharge

on page 47)

Verify the contents in the server box (

Server box contents

on page 48).

Install hardware options (

Hardware options installation

on page 50).

Install the server into a rack (

Installing the server into the rack

on page 34).

Configure the server (

Configuring the server

on page 48).

Install or deploy an operating system (

Installing or deploying an operating system

on page 48).

Registering the server

on page 49).

Operational requirements

Space and airflow requirements

To allow for servicing and adequate airflow, observe the following space and airflow requirements when
deciding where to install a rack:

Setup

Summary of Contents for BCD221






























































































































































Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands

BCDVideo BCD221, User Manual

Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands