BCDVideo BCD221 User Manual Download Page 11

Page: 11 / 157

Item

Description

Status

NIC status LED*

Solid green = Link to network

Flashing green (1 Hz/cycle per sec) = Network active

Off = No network activity

UID button/LED*

Solid blue = Activated

Flashing blue:

• 1 Hz/cycle per sec = Remote management or

firmware upgrade in progress

• 4 Hz/cycle per sec = iLO manual reboot sequence

initiated

• 8 Hz/cycle per sec = iLO manual reboot sequence

in progress

Off = Deactivated

*When all four LEDs described in this table flash simultaneously, a power fault has occurred. For more
information, see "

Power fault LEDs

**If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the
system health status.

†Facility power is not present, power cord is not attached, no power supplies are installed, power supply
failure has occurred, or the power button cable is disconnected.

LFF 12-drive model front panel LEDs and button

Component identification

Summary of Contents for BCD221






























































































































































Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands

BCDVideo BCD221, User Manual

Search results

Summary of Contents for BCD221

Reviews:

Related manuals for BCD221

Brands by name

Popular brands