manualshive.com logo in svg

BCDVideo BCD221, User Manual, Page: 112 / 157

Share
Download
BCDVideo BCD221 User Manual Download Page 112

The installation is complete.

HPE Trusted Platform Module 2.0 

Overview

Use these instructions to install and enable an HPE TPM 2.0 Kit in a supported server. This option is

 

not 

supported on Gen9 and earlier servers.

This procedure includes three sections:

1.

Installing the Trusted Platform Module board.

2.

Enabling the Trusted Platform Module.

3.

Retaining the recovery key/password.

HPE TPM 2.0 installation is supported with specific operating system support such as Microsoft

®

 Windows

Server

®

 2012 R2 and later. For more information about operating system support, see the product

QuickSpecs on the Hewlett Packard Enterprise website (

http://www.hpe.com/info/qs

). For more information

about Microsoft

®

 Windows

®

 BitLocker Drive Encryption feature, see the Microsoft website (

http://

www.microsoft.com

).

CAUTION:

Chipset-TPM is not available after power is removed from the system and the HPE TPM 2.0 Kit

 

is 

installed. Do not install the HPE TPM 2.0 Kit if Chipset-TPM is enabled and the operating

 

system is 

using Chipset-TPM features. Otherwise, the OS may go into recovery mode, data loss can

 

occur, or 

both. If an OS is installed and using Chipset-TPM, follow the OS vendor instructions to disable

 

the OS 

TPM features before changing any TPM functionality.

CAUTION:

Any attempt to remove the cover of an installed TPM from the system board can damage the TPM
cover, the TPM, and the system board. If the TPM is removed from the original server and powered up
on a different server, data stored in the TPM including keys will be erased.

112

  HPE Trusted Platform Module 2.0 Option

Summary of Contents for BCD221






























































































































































Reviews:

No comments