manualshive.com logo in svg

BCDVideo BCD221, User Manual, Page: 50 / 157

Share
Download
BCDVideo BCD221 User Manual Download Page 50

Hardware options installation

Product QuickSpecs

For more information about product features, specifications, options, configurations, and compatibility, see the
product QuickSpecs on the Hewlett Packard Enterprise website (

http://www.hpe.com/info/qs

).

Introduction

If more than one option is being installed, read the installation instructions for all the hardware options and
identify similar steps to streamline the installation process.

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system
components to cool before touching them.

CAUTION:

To prevent damage to electrical components, properly ground the server before beginning any
installation procedure. Improper grounding can cause electrostatic discharge.

Installing the bezel and bezel lock

50

 Hardware options installation

Summary of Contents for BCD221






























































































































































Reviews:

No comments