Baxi Bioflo 12 kW Pear User Operating Instructions Manual Download | Manualshive

Page: 53 / 60

background image

52

Troubleshooting

4.2

Information messages

Code Meaning/effect

Cause/remedy

IN 581

Replenish fuel

The reserve supply container is almost
empty. Top up pellets.

Boiler continues to heat until the remaining fuel quantity has been consumed.

a) FireWIN Klassik (without feed):

Fill fuel into the fuel container (see section 2.3).

b) FireWIN Premium/Exklusiv (with feed): Feed is switched off in „feed ope-

rating mode“ (see section 2.8.1.2). In „Feed operating mode“ menu item,
set to „with enable time“, „with start time“ or „without time control“.

IN 582

Reserve supply container empty

The reserve supply container is empty.
Top up pellets. Burner is locked.

The reserve supply container is empty.

a) FireWIN Klassik without feed:

Fill fuel into the fuel container (see section 2.3).

b) FireWIN Premium/Exklusiv (with feed):

Feed is switched off in „feed operating mode“ (see section 2.8.1.3). In „Feed
operating mode“ menu item, set to „with enable time“, „with start time“
or „without time control“.

IN 590

Clean boiler and burner

Perform cleaning and confirm in opera-
tor level.

Boiler and burner are still operating.

Boiler and burner must be cleaned or the both ash pan(s) (see Fig. 162) emp-
tied (see sections 3.4, 3.5 and 3.6). Following cleaning, confirm cleaning on
the InfoWIN operator level (see section 2.8.1.1).

IN 595

Door open

Burner locked. Only open the door
when the burner is switched off.

Cladding door is open, burner locked.

a) Close the cladding door.

b) Door switch on cladding door does not switch correctly, adjust – see instal-

lation instructions.

Code Meaning/effect

Cause/remedy

–

No display

Boiler is off, cannot be switched on with
the ON/OFF button.

a) No electricity, check the cable to the device and the building fuse.

b) No electricity, device fuse defective – check and replace if necessary – see

page 55, Fig. 163.

c) InfoWIN plug loose or poorly connected together if connected at all during

installation – check and connect together firmly if necessary, plug is loca-
ted on the side at the top behind the right side panel cladding – see instal-
lation instructions; Installing the cladding.

4.1

No display on InfoWIN

«
...
51
52
53
54
55
...
»

Summary of Contents for Bioflo 12 kW Pear





























































Reviews:

No comments

Related manuals for Bioflo 12 kW Pear

Brand: Ideal Boilers Pages: 8

Brand: RBI Pages: 20

Brand: Kalor Pages: 54

Brand: Navien Pages: 4

Brand: Lang Pages: 16

Brand: Cecilware Pages: 11

ECO HEAT 10 CA II PLUS

Brand: Gorenje Pages: 74

Brand: Vulcan-Hart Pages: 2

Brand: Zojirushi Pages: 38

Brand: Baxi Pages: 36

Brand: Kiturami Pages: 20

Logano plus SB315

Brand: Buderus Pages: 16

Maxflow Combi FS

Brand: Baxi Pages: 48

Main Combi 25 Eco

Brand: Baxi Pages: 60

MainEco Combi 24

Brand: Baxi Pages: 80

Elite FT EFT-285

Brand: HTP Pages: 70

Brand: HTP Pages: 74

Brand: Termomont Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands