Bauer RAINSTAR T32 Series Operating Manual Download Page 71

Page: 71 / 72

Operation manual for

BAUER RAINSTAR

Series T32, T42

18 TROUBLE

SHOOTING

FAULT

CAUSE

REMEDY

PE-pipe cannot be pulled off.

Gear shift lever in wrong position

Move to pull-off position.

Brake band sticking on the brake drum. Loosen brake band.

PE-pipe retraction stops before
final shut-off activated.

Turbine blocked by foreign object.

Remove foreign object.

Pressure drop in supply line.

Check pumping station and water
connection at the hydrant.

Overwinding PE-pipe actuates the
safety shut-off.

Adjust the winding mechanism.

Repair broken winding chain.

Final shut-off activated but the
shut-off valve does not close.

Values set for shut-off are not correct. Adjust

setting

according

instructions.

Thin plastic hose of shut-off valve is
blocked up or broken.

Replace the plastic hose.

The reel overwinds during pull-
off or the PE-pipe windings
become loose.

Tractor stopped abruptly.

Slow down gradually.

Loose brake setting.

Adjust brake.

No oil in change-speed gearbox.

Refill oil.

Retraction speed varies from
one PE-pipe layer to the next.

Varying ground conditions.

Adjust speed control system to
the ground conditions (Change
rod position on the lever of the
layering mechanism. )

The desired retraction speed is
not reached.

Incorrect transmission.

Select correct transmission.

Sprinkler nozzle blocked.

Remove foreign object.

General: compare supply pressure and water flow with performance chart
values.

Cart is not lifted

Wrong gearbox transmission

Select correct transmission.

Water is running out at

the reel supply (flange bow)

Lip seal or sealing bush damaged

Replace affected parts

Summary of Contents for RAINSTAR T32 Series









































































Search results

Summary of Contents for RAINSTAR T32 Series

Reviews:

Related manuals for RAINSTAR T32 Series

Brands by name

Popular brands

Bauer RAINSTAR T32 Series, Operating Manual

Search results

Summary of Contents for RAINSTAR T32 Series

Reviews:

Related manuals for RAINSTAR T32 Series

Brands by name

Popular brands