Bauer RAINSTAR T32 Series Operating Manual Download Page 46

Page: 46 / 72

Operation manual for

BAUER RAINSTAR

Series T32, T42

OPTION - SMS

The ECOSTAR 4300 can be operated with an external MC52i-GSM-Modem by Cinterion.

By sending an SMS the RAINSTAR can be started or stopped and the status can be requested.

Commands

Start

Starts the machine.

Stop

Stops the machine.

Speed ###

set the

speed

between 3 and 400 m/h.,

e.g.:

speed 24

Status

Shows the current status of the machine.

SMS can be typed in both upper- or lower case or mix .

If you call the modem from a GSM-telephone you will receive an SMS with the

Status

If the machine is operated by keyboard (display is lighted) the SMS-function is deactivated in order to
prevent multiple sms and to block remote operating. When receiving an SMS

User active

is sent retun.

Status

SPEED 30.0m/h
DOSE 22 mm
TIME 14:10 STOP18:16
STATUS OPERATION

DISTANCE 123M
BATTERY 12.8V
CHARGE ON 0.231A

SMS, sent by PR10-12, contains information about
irrigation.

The following messages are sent by SMS:

PRESSURE LOW:

Start pump, to get pressure on the machine.

STOP SENSOR:

The machine can be moved to a new field

STOP REMOTE:

The machine was stopped by an SMS,

STOP DISTANCE:

The machine has reached stop point (constant 8)

MONITORING TIME:

The machine has not moved for nn minutes (Constant 4) due to a
malfunction. Check the machine before continuing.

Summary of Contents for RAINSTAR T32 Series









































































Search results

Summary of Contents for RAINSTAR T32 Series

Reviews:

Related manuals for RAINSTAR T32 Series

Brands by name

Popular brands

Bauer RAINSTAR T32 Series, Operating Manual

Search results

Summary of Contents for RAINSTAR T32 Series

Reviews:

Related manuals for RAINSTAR T32 Series

Brands by name

Popular brands