Bauer RAINSTAR T32 Series Operating Manual Download Page 12

Page: 12 / 72

Operation manual for

BAUER RAINSTAR

Series T32, T42

4 WARNING

SYMBOLS

Danger points on the RAINSTAR are specifically marked by safety stickers. These stickers must be affixed to the
mentioned points clearly visible. They serve to protect persons working on or near the system.

1.

WARNING !

Study and observe the manual and all safety instructions carefully before you put

the system into operation.

WARNING !

Before any service and repair work, always stop the machine and read the

operating manual

WARNING !

1. The operating range of the RAINSTAR must always be at a safe distance

from electric power lines.

2. This applies to both wide-range sprinklers and machines operating with

boom cart AS 26/32.
The water jet of spray nozzles and sprinklers must not reach electric power
lines.

WARNING !

Never remove safety covers while system is operating.
Make sure that the RAINSTAR’s reel does not move during repairs. Slacken the
PE-pipe.

WARNING !

Keep away from the rear of the RAINSTAR!!
Danger of bruising by the incoming sprinkler cart. Keep your distance!

Summary of Contents for RAINSTAR T32 Series









































































Search results

Summary of Contents for RAINSTAR T32 Series

Reviews:

Related manuals for RAINSTAR T32 Series

Brands by name

Popular brands

Bauer RAINSTAR T32 Series, Operating Manual

Search results

Summary of Contents for RAINSTAR T32 Series

Reviews:

Related manuals for RAINSTAR T32 Series

Brands by name

Popular brands