manualshive.com logo in svg

Baroness GM2810A, Owner'S Operating Manual, Page: 57 / 155

Share
Download
Baroness GM2810A Owner'S Operating Manual Download Page 57

Check that the number at the right of
the parameter disappeared.

ENGINE  SPEED                      

                 

DRIVERS  DEMAND  ENGINE  TORQUE   4
ACTUAL  ENGINE  TORQUE                     3
PERCENT  LOAD  AT  CURRENT  RPM      
ACCELERATOR  PEDAL  POSITION    1    2
ENGINE  DESIRED  OP  SPEED
ENGINE  COOLANT  TEMPERTURE
FUEL  RATE
THROTTLE  POSITION

vjgml4-023

Custom Setup_011

Press the menu key and check that
the parameter has changed to
"EMPTY".

EMPTY

0.0 %

0 %

0 %

ENG TORQ

DEMAND TQ

ACCEL PED1

vjgml4-024

Custom Setup_012

Pressing the menu key once returns to the
display for selecting the page.
To change other parameters, repeat steps
3 to 5.

Service Reminders

With "SERVICE REMINDERS", the
notification of replacement time for the
following 5 consumables can be specified.

Engine oil
Engine oil filter
Hydraulic oil
Hydraulic oil filter
Air cleaner

The following 2 items appear when "SERVICE
REMINDERS" is selected.

RESET REMINDERS
MODIFY REMINDERS

b.

c.

5.

6.

･
･
･
･
･

･
･

Reset Reminders

With "RESET REMINDER", displayed
remaining time can be reset to the time
specified with "MODIFY REMINDERS".

Press the menu key.
After the main menu appears, use the
arrow keys to highlight "SERVICE
REMINDERS", and then press the Enter
key.

3

1

2

SERVICE  REMINDERS

SELECT  UNITS
ADJUST  BACKLIGHT
ADJUST  CONTRAST
UTILITIES

unpc8m-006

Reset Reminders_001

1

Menu key

2

Arrow keys

3

Enter key

Highlight "RESET REMINDER", and then
press the Enter key.

RESET  REMINDERS

MODIFY  REMINDERS

unpc8m-007

Reset Reminders_002

￭

1.

2.

Description of Functions

GM2810A

Description of Functions

Page 4-21

Monitor

Summary of Contents for GM2810A




























































































































































Reviews:

No comments