manualshive.com logo in svg

Baroness GM2810A, Owner'S Operating Manual, Page: 56 / 155

Share
Download
Baroness GM2810A Owner'S Operating Manual Download Page 56

The parameters appear.
The number at the right of the
parameter indicates the location in the
4-up display.
1=Upper left
2=Lower left
3=Upper right
4=Lower right

ENGINE  SPEED                                      1

DRIVERS  DEMAND  ENGINE  TORQUE   4
ACTUAL  ENGINE  TORQUE                     3
PERCENT  LOAD  AT  CURRENT  RPM
ACCELERATOR  PEDAL  POSITION    1    2
ENGINE  DESIRED  OP  SPEED
ENGINE  COOLANT  TEMPERTURE
FUEL  RATE
THROTTLE  POSITION

vjgml4-019

Custom Setup_005

0 RPM

0.0 %

0 %

0 %

ENG TORQ

ENG RPM

DEMAND TQ

ACCEL PED1

vjgml4-018

Custom Setup_006

To change to a different parameter

Use the arrow keys to highlight the
parameter to be selected, and then
press the Enter key.

ENGINE  SPEED                                      1                                       
DRIVERS  DEMAND  ENGINE  TORQUE   4
ACTUAL  ENGINE  TORQUE                     3

PERCENT  LOAD  AT  CURRENT  RPM      

ACCELERATOR  PEDAL  POSITION    1    2
ENGINE  DESIRED  OP  SPEED
ENGINE  COOLANT  TEMPERTURE
FUEL  RATE
THROTTLE  POSITION

vjgml4-020

Custom Setup_007

[3]

[4]

a.

Check that a number appeared to the
right of the selected parameter.

ENGINE  SPEED                                       
DRIVERS  DEMAND  ENGINE  TORQUE   4
ACTUAL  ENGINE  TORQUE                     3

PERCENT  LOAD  AT  CURRENT  RPM     1

ACCELERATOR  PEDAL  POSITION    1    2
ENGINE  DESIRED  OP  SPEED
ENGINE  COOLANT  TEMPERTURE
FUEL  RATE
THROTTLE  POSITION

vjgml4-021

Custom Setup_008

Press the menu key and check that
the parameter has changed.

0 %

0.0 %

0 %

0 %

ENG TORQ

ROAD  RPM

DEMAND TQ

ACCEL PED1

vjgml4-022

Custom Setup_009

To deselect a parameter and remove it
from the list of displayed parameters

Highlight the parameter to be
removed, and then press the Enter
key.

ENGINE  SPEED                                      1

DRIVERS  DEMAND  ENGINE  TORQUE   4
ACTUAL  ENGINE  TORQUE                     3
PERCENT  LOAD  AT  CURRENT  RPM
ACCELERATOR  PEDAL  POSITION    1    2
ENGINE  DESIRED  OP  SPEED
ENGINE  COOLANT  TEMPERTURE
FUEL  RATE
THROTTLE  POSITION

vjgml4-019

Custom Setup_010

b.

c.

[5]

a.

GM2810A

Description of Functions

Page 4-20

Monitor

Summary of Contents for GM2810A




























































































































































Reviews:

No comments