manualshive.com logo in svg

Baroness GM2810A, Owner'S Operating Manual, Page: 139 / 155

Share
Download
Baroness GM2810A Owner'S Operating Manual Download Page 139

The items above (*3 marked) are registered as emission related critical parts by KUBOTA in the
U.S. EPA nonroad emission regulation.
As the engine owner, you are responsible for the performance of the required maintenance on the
engine according to the above instruction.
Please see the Engine's Warranty Statement in detail.
*4: Refer to the Engine's Owner's Manual.
*5: Refer to the Battery's Owner's Manual.
The values for consumables are not guaranteed.
*6: Be sure to replace hydraulic hoses for steering cylinder and hydraulic hoses for hydraulic motor
of wheel relating to steering every two years.

List of Adjusted Value

Fan belt

7.0 - 9.0 mm (0.28 - 0.35 in)

Belt slack
when belt pressed with 98 N (10 kgf) at the
middle point.

Brake

0.2 mm (0.0079 in)

Clearance between the brake disc and the
pad

1.0 mm (0.039 in)

Play at the connection of the inner wire

･

･
･
･
･

Appended Table

GM2810A

Appended Table

Page 8-11

List of Adjusted Value

Summary of Contents for GM2810A




























































































































































Reviews:

No comments