manualshive.com logo in svg

Bailey 40 Series, Hardware Manual

Share
Download
Bailey 40 Series Hardware Manual Download Page 72

COMPONENT DESCRIPTION AND REPLACEMENT

POWER SUPPLY REMOVAL

I-E96-192-5A   

6 - 9

IIOIC423 Environmental Cabinet

To remove the power supply from an  IIOIC423 environmental
cabinet see Figure 

6-7

 and follow these steps:

1. Follow the procedure for removing the IIOIC423 power
entry panel in this section.

2. Remove the IIMKM02A circuit board. Do not lose the two
nonconductive washers for each standoff. 

3. To remove the cover from the top of the power entry panel,
remove the nine screws shown in the figure and disconnect the
DC distribution board connector.

4. Mark and disconnect the wires between the power supply
and incoming AC. 

5. Remove the four screws holding the power supply to the
center support wall of the power entry panel. 

NOTE: Check that the DC distribution board connector to the power
supply is aligned correctly when replacing the cover.  

Figure 6-7.  Power Supply Removal for IIOIC423 Environmental Console

3 SCREW S
ON COVER

4 SCREW S ON CENTER
SUPPORT WALL

POW ER SUPPLY

3 SCREW S
ON COVER

TP35370B

3 SCREW S
ON COVER

MKM BOARD

4 SCREW S

DC DISTRIBUTION

BOARD

DC DISTRIBUTION
BOARD CONNECTOR

NOTE: DO NOT LOSE NON-CONDUCTIVE
WASHERS ON MKM BOARD STANDOFFS

FRONT VIEW

Summary of Contents for 40 Series








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands