background image

INSTALLATION

OPERATOR INTERFACE DEVICES

I-E96-192-5A   

 

3 - 21

IIOIC424 Panel Mount Wiring Connections and Cabling

The IIOIC424 panel mount console is internally wired when it
is shipped. Connect the AC power and any peripheral devices.
The power entry panel provides line filtering, transient sup-
pression and a ten-amp circuit breaker. 

1. Plug in AC power to the power connector. 

2. Refer to Figure 

3-15

 for AC input location. 

Cable connections are shown in Figure 

3-16

. Table 

3-5

 is a list

of the cable connections.  

 OPERATOR INTERFACE DEVICES

This section contains information and the installation instruc-
tions for the operator and engineering keyboards, mouse/
trackball and the annunciator display panels. 

Operator Keyboard

The KEYBOARD port on the keyboard interface assembly is for
the mylar operator keyboard. The 0.9 meters (3-foot) long
coiled cord can be stretched to 2.4 meters (8 feet). See Figure

3-17

. Refer to Table 

7-1

 for the operator keyboard part

number.

Engineering Keyboard

Each IIOIC42 console supports an additional engineering key-
board (QWERTY) (Figure 

3-18

). A 6-pin mini DIN to 5-pin DIN

adapter is supplied with the keyboard. All OIC consoles have a
five-pin DIN connector located on the keyboard interface
board. Power does not have to be removed from the OIC con-
sole before plugging in or unplugging the keyboard. Initializing
the system is not needed after plugging in or unplugging the
keyboard. Keyboard mapping information is in the operation
instruction. 

       

Figure 3-15.  IIOIC424 Panel Mount Power Entry Panel Connections

TP36136D

.

TO ADP (IF USED)

TO KEYBOARD

PORT

J2

I/O PW R

ADP PW R

FAN PW R

CPU INPUT PW R

POW ER

W RIST
STRAP

PEP INPUT PW R

J1

TO COMMUNICATION

PORT

TO KEYBOARD

CONNECTOR PANEL

KEYBOARD

RESET

DEGAUSS

ADP

2
NO

1
NO

4
NO

3
NO

6
NO

5
NO

2
NC

1
NC

4
NC

3
NC

6
NC

5
NC

2
CO

1
CO

4
CO

3
CO

6
CO

5
CO

DI
2+

DI
1+

DO
2+

DO
1+

DI
2–

DI
1–

DO
2–

DO
1–

Summary of Contents for 40 Series








































































































Reviews: