manualshive.com logo in svg

Axis 5600+, User Manual

Share
Download
Axis 5600+ User Manual Download Page 54

Ne

tW

ar

e

Section 5: Setting Up - NetWare

 

AXIS 5600+ User’s Manual

 

54

 

Section 5 Setting Up - NetWare 

This section describes how to continue the installation of the AXIS 
5600+ in the NetWare environment. Identify which transport 
protocol you are running on your network and which installation 
method you should use. Continue the installation by selecting the 
appropriate installing instructions from the table below:

If you intend to operate your AXIS 5600+ in a multi-protocol, mixed 
environment, you should also proceed to the other relevant sections in 
this manual, namely:

Section 4  Setting Up - Windows

, on page 34

Section 6  Setting Up - OS/2

, on page 68

Section 7  Setting Up - Macintosh

, on page 74

Section 8  Setting Up - UNIX

, on page 80

Installation 
method

Transport 
protocol

Action

NDPS

TCP/IP

IPX/SPX

See 

Setup using NDPS

, on page 55

Proceed with 

Installing the AXIS 5600+ in an NDPS environments

, on 

page 55.

Queue based 
printing

IPX/SPX

Basic 
Configuration

To install using the AXIS NetPilot Installation Wizard, see 

Basic Setup 

with AXIS NetPilot

, on page 58.

IPX/SPX

Advanced 
configuration 

If you need a more advanced installation that is not covered by the AXIS 
NetPilot Installation Wizard, continue with 

Advanced Installation using 

AXIS NetPilot

, on page 61.

Pure IP

See 

Basic Queue-based printing over IP

, on page 64

Summary of Contents for 5600+






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands