manualshive.com logo in svg

Axis 5600+, User Manual

Share
Download
Axis 5600+ User Manual Download Page 156

Ne

tW

ar

e

UNIX

Wi

n

d

ow

s

OS

/2

Ma

ci

ntosh

Section 14: Technical Specifications

 

AXIS 5600+ User’s Manual

 

156

 

Supported Protocols

NetWare:

IPX, SAP, RIP, SPX, SNMP, NCP (extended with NDS), NLSP, 
DIAG, TCP/IP.

Windows and OS/2:

NetBIOS/NetBEUI or TCP/IP, WINS.

LANtastic

NetBIOS/NetBEUI.

TCP/IP:

LPD, FTP, Telnet, Reverse Telnet, PROS, BOOTP, ARP, RARP, 
DHCP ICMP, Auto-IP, IP, TCP, UDP, HTTP, SNMP, TFTP, 
SLPv2, Dynamic DNS, IPP.

Apple EtherTalk:

AARP, ATP, DDP, NBP, PAP, RTMP, ZIP.

Network Management

SNMP-MIB II compliant (over UDP/IP and IPX), host resource MIB 
compliant (over UDP/IP and IPX), private enterprise MIB included. 
LAN Network Manager for OS/2. Print server status in 
NWAdmin/PCONSOLE.

Hardware

32 bit 100 MHz RISC Controller, 1 Mbyte Flash memory. 2 MB 
RAM.

Logical Connection

NWay support to provide auto-detection of the network speed. 
Running simultaneously any combination of the supported protocols. 
Use of IEEE802.2, IEEE802.3, SNAP and Ethernet II frame types 
simultaneously.

Attachments

RJ-45 connector (Category 5 Unshielded Twisted Pair) for 10baseT 
Ethernet and 100baseTX Fast Ethernet.

Security

UNIX:

Root password. User access list and printer access.

NetWare:

Encrypted passwords. Packet Signature supported.

Summary of Contents for 5600+






































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands