AVL 9120 Service Manual Download Page 44

Page: 44 / 114

10 Service Functions Menu - 9181

Test Valve C:

YES/NO=ON/OFF

SERVICE

FUNCTIONS?

CALIBRATION?

Test

Electrodes?

Test

Standard A *?

Std. A*: Na = 0000

K = 0000 Ca = 0000

Test

External Sample?

Introduce Sample

Retract Probe

-> YES

Ext.: Na = 0000

K = 0000 Ca = 0000

Remain in

Test Electrodes?

Test

Sample Sensor?

DRY: 80-120: 102

YES=Pump/NO=Exit

External: 102

Pump: NO=OFF

wash...

Test

Probe?

Test Pump?

Test Valves?

Test Pump!

Very slow speed

Test Pump!

Slow speed

Test Pump!

Medium speed

Test Pump!

Fast speed

Test Valve A:

YES/NO=ON/OFF

Test Valve B:

YES/NO=ON/OFF

Test Valve V:

YES/NO=ON/OFF

Test Interface?
Jump Pins 2&3

Test

Amplifier?

Enter

Service Code?

Na = -1030 K = -1200
Cl = -1093

Ground = 2

-2500mV = -2496

Remain in

Test Interface?

Enter Code:

AAA ok?

Enter Other

Service Code?

NA K CA READY

Calibration?

Remain in

Service Func?

-- Test --

-- Interface --

Interface

ok!

Code

Accepted!

Calibrate...

Is Code

valid?

YES

Test

SnapPak Sensor?

Test

Language Switch?

SnapPak: I

I=In O=Out

Language Switch

English

YES

YES/NO

YES

Test Valve R:

YES/NO=ON/OFF

Code Error!

Retry?

YES

Temp (mV) = -2670

Temp (°C) = 26.2

*same for Std. A, B, C

YES

Test

Sampler?

Probe moves

to extended

position

U = 0 L = 1

Sample Position?

U = 0 L = 0

Upper Position?

U = 0 L = 0

Cup Position?

U = 0 L = 0

Lower Position?

U = 0 L = 1
Exit Probe Test?

Probe moves

to upper

position

Probe moves

to cup position

Tray moves to

cup position

Probe moves

to upper

position

Tray moves to

mid position

Probe moves

to lower
position

Probe moves

to upper

position

Tray homes

Probe moves

to lower
position

YES

Summary of Contents for 9120



















































































































Search results

Summary of Contents for 9120

Reviews:

Related manuals for 9120

Brands by name

Popular brands

AVL 9120, Service Manual

Search results

Summary of Contents for 9120

Reviews:

Related manuals for 9120

Brands by name

Popular brands