AVL 9120 Service Manual Download Page 59 | Manualshive

Page: 59 / 114

background image

53

4.2.5 Main Tube Set

The main tube set is supplied as a pre-cut tubing harness with the fluidic inter-
connections preassembled. Replacement of the tube set should be performed
annually. For removal of the tubing, first remove the ISE SnapPak

TM

from the

reagent compartment. This will allow access for removal of the white TPR
block which is the main interconnection between the ISE SnapPak

TM

and the

tubing. This block can be removed by grasping the front surface and pulling
forward. Next, remove tubing from each solenoid valve. Follow the procedure
outlined in Section 4.1.5 for disassembly of the solenoid valves to enable fluidic
tubing to be easily removed at each solenoid. Pull the two pump windings at the
peristaltic pump tube set off the pump roller and remove the white reference
solution tube connector. Remove the white TPR reference solution block by
grasping the front of the block and pulling forward. The three tube connections
are labeled with green, blue and red tags. All remaining tubes can now be
removed and the entire tubing harness can be discarded.

Fit the replacement tubing harness and assemble in reverse order as disassem-
bly. Reference the Tube Diagram on the next page for correct tube locations.

«
...
57
58
59
60
61
...
»

Summary of Contents for 9120



















































































































Reviews:

No comments

Related manuals for 9120

Brand: Kanomax Pages: 2

Brand: Keithley Pages: 156

Brand: Accurate Logic Pages: 50

Acuvim-L Series

Brand: AccuEnergy Pages: 188

Brand: VAMP Pages: 78

Brand: Narvitech Pages: 2

Brand: Sensia Pages: 16

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Lake Shore Cryotronics Pages: 97

Brand: YOSensi Pages: 27

Brand: Jula Pages: 9

LISST-PORTABLE XR

Brand: Sequoia Pages: 41

Brand: Bruker BioSpin Pages: 76

Brand: FASAR ELETTRONICA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands