AVL 9120 Service Manual Download Page 52 | Manualshive

Page: 52 / 114

background image

46

DEC CED

Provides one additional digit of resolution for each
measured parameter for blood and serum samples.
QC and Standard samples are always displayed with
high resolution. Urine samples are always displayed in
low resolution.

ECO OCE

Allows the operator to run the instrument in the
economy mode. The instrument will enter the

STANDBY MODE

. This occurs at the time of the

next 2-point calibration when no samples have been
analyzed since the last 2-point calibration.

FIF

IFI

Allows printing of electrode voltages during printout
of measurements and calibrations.
(not available for 9140)

LEM MEL

This service code will print the last 20 error messages

(9180/9181 only)

with the date and time of occurrence.

MGL LGM

This service code is available only in the model 9140/
9180/9181 analyzer and enables Ca

++

values to be

displayed in mg/dL. The normal mode displays values in
mmol/L. QC and Standard results are always displayed
in mmol/L.

NOB BON

This service code disables the beep.

(9180 /9181only)

QCC CCQ

When this code is enabled, QC values will be reported in
direct ISE measurement instead of flame-equivalent
values. In this mode, correlation factors are NOT
applied to the measured values.

SFC

This code allows the input of a percentage for the ISE

(9180/9181 only)

SnapPak

TM

counter.

SLC

CLS

When this code is set, the current setting of the leasing

(9180/9181 only)

counter, which cannot be reset by the operator, is
printed on the calibration report.

SSC CSS

This code toggles needle height to accommodate smaller

(9181 only)

sample cups. In the default setting, the analyzer works
with 2.0 mL cups. To select 0.25 mL sample cups,

SSC

has to be activated. To return to the default

setting,

CSS

has to be activated.

«
...
50
51
52
53
54
...
»

Summary of Contents for 9120



















































































































Reviews:

No comments

Related manuals for 9120

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 63

Brand: WattNode Pages: 57

Brand: Kanomax Pages: 31

Brand: Hach Pages: 196

Brand: Makita Pages: 2

Brand: Makita Pages: 16

Brand: Hama Pages: 6

Brand: Oceanic Pages: 68

Brand: Oceanic Pages: 24

Brand: PASCO Pages: 3

Brand: PASCO Pages: 2

Brand: NanoPhotometer Pages: 133

Brand: Vega Pages: 28

Brand: Vega Pages: 20

Brand: Xantrex Pages: 2

Brand: Xaoc Devices Pages: 8

Brand: Zeversolar Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands