AVL 9120 Service Manual Download Page 74

Page: 74 / 114

REPLACE FLUID PACK

When the monitored fluid level in the

ISE SnapPak

reaches 5% remaining,

the analyzer will print

REPLACE FLUID PACK

at the end of each sample

report. This message is printed only. Replace the

ISE SnapPak

following

the instructions outlined in the Operator Manual.
To maximize the life of the

ISE SnapPak

, continue running the analyzer until

STANDARD A NOT DETECTED

message is displayed. This will

ensure that the

ISE SnapPak

is completely depleted before replacement.

CHECK TEMPERATURE

(9140/9180/9181 only)

On the 9140/80/81 models, the analyzer will display

CHECK

TEMPERATURE

at the end of each measurement, if the temperature

measured is out of range (10.0°C to 40°C). The temperature sensor is located
in the right side electrode holder.

Possible causes and remedies:

•

Ensure that the sample sensor cable is securely plugged in.

•

Check whether room temperature is within specified limits
(15°C to 32°C / 60°F to 90°F).

•

Perform temperature adjustment procedure.

•

Replace SBC board or right side electrode holder.

VALVE OVERTEMP! CHECK VALVES

In case one of the valve solenoids overheats, the message

VALVE

OVERTEMP! CHECK VALVES

will be displayed. Each solenoid

incorporates a thermo-fuse, which will reset automatically.

Possible causes and remedies:

•

Turn power off for at least one hour.

•

Check fuse F3 (24V).

•

Check whether room temperature is within specified limits
(15°C to 32°C / 60°F to 90°F).

Summary of Contents for 9120



















































































































Search results

Summary of Contents for 9120

Reviews:

Related manuals for 9120

Brands by name

Popular brands

AVL 9120, Service Manual

Search results

Summary of Contents for 9120

Reviews:

Related manuals for 9120

Brands by name

Popular brands