AVL 9120 Service Manual Download Page 50 | Manualshive

Page: 50 / 114

background image

44

TEST PROBE

(9181 only)

This test verifies the operation of the sample probe motor, position sensor and
associated circuitry. The "U" represents the output of the upper position sensor, the
"L" represents the output of the lower position sensor.

Example Display:

U = 0 L = 1
Sample Position?

TEST AUTOSAMPLER

(9181 only)

This test verifies the operation of the Autosampler turntable assembly. The display
indicates the output of both the position and home sensors.

Note: If the Autosampler is not plugged in or the

TABLE PRESENT

bit is

not activated, this test will not appear under the

SERVICE FUNCTIONS

menu.

Example Display:

Home: 0
Pos = 1

TEST PUMP

This test turns on the peristaltic pump at each of the four pump speeds. The display
indicates for two seconds each pump speed while each pump speed is being tested.
Observe that the peristaltic pump changes speed as is indicated on the display.

*** Pump Test *** *** Pump Test ***
Very Slow Speed Slow Speed

*** Pump Test *** *** Pump Test ***

Medium Speed Fast Speed

«
...
48
49
50
51
52
...
»

Summary of Contents for 9120



















































































































Reviews:

No comments

Related manuals for 9120

Brand: QLA Pages: 18

LM-OG-P2 Advanced

Brand: Badger Meter Pages: 48

Brand: Badger Meter Pages: 24

Brand: Bahco Pages: 92

Brand: Galileo Pages: 19

Brand: Galileo Pages: 71

Brand: Oldham Pages: 34

Brand: velocomp Pages: 4

Brand: Rabid Elephant Pages: 18

SoundTrack LxT N/Forcer

Brand: Larson Davis Pages: 12

Brand: Mark-10 Pages: 26

Brand: SIGLENT Pages: 32

Brand: Teledyne Pages: 85

DGX Gears XTRA Regulator

Brand: Dive Gear Express Pages: 26

Brand: POSEIDON Pages: 13

Brand: Magnescale Pages: 2

Brand: A&D Pages: 2

Brand: Hammond Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands