AVL 9120 Service Manual Download Page 66 | Manualshive

Page: 66 / 114

background image

60

5.2 Error Messages and Troubleshooting

STATUS: NOT CALIBRATED

This message is only displayed when a calibration has been interrupted by
pressing

NO

or opening the sample door. Perform a calibration to return to the

READY

Mode.

STANDARD A NOT DETECTED

This message is displayed when the sample sensor is unable to properly detect
the Standard A solution in a programmed time period. As the analyzer draws a
sample of Standard A, the leading edge of the solution is detected by the
sample sensor. The sample sensor must also detect a continuous flow of
Standard A Solution into the sample chamber, lasting several seconds, without
encountering air bubbles or air. After several seconds, the trailing edge of the
Standard A sample is sensed, the peristaltic pump stops and measurement
occurs.

Possible causes and remedies:

•

Check for air leaks preventing the Standard from being drawn into the
chamber. Ensure that all O-rings are in place. There must be a
continuous draw of standard solution, free of air bubbles.
Check solenoid V for proper sealing of the vent line.
Check fill port to ensure the absence of air leaks.

•

Check for clots or crystals formed in the Standard A tubing or
electrode chamber.

•

Ensure that the sample sensor is plugged in securely and perform
Sample Sensor Test to ensure sensor is operating correctly. Clean,
adjust or replace sample sensor to correct sample sensor operation.

•

Replace peristaltic pump tube set to ensure proper sample aspiration.

•

Check the fluid remaining in the

ISE SnapPak

TM

. If less than 5%

remains, replace the

ISE SnapPak

TM

.

«
...
64
65
66
67
68
...
»

Summary of Contents for 9120



















































































































Reviews:

No comments

Related manuals for 9120

Brand: K-Patents Pages: 10

Brand: OBDPROG Pages: 8

Brand: Danfoss Pages: 80

Brand: Oldham Pages: 96

Brand: BD Sensors Pages: 4

Brand: Roland Pages: 2

Brand: Karman Pages: 2

Brand: Hanna Pages: 44

Brand: Hauber Elektronik Pages: 28

Multimar 25 EWR

Brand: Mahr Pages: 20

Brand: Fluke Pages: 8

Brand: Quadelectra Audioworx Pages: 12

HydroTracer FLV HT2

Brand: aboni Pages: 48

MoistureMaster Compact Plus

Brand: LaserLiner Pages: 80

Brand: SIGRIST Pages: 54

Brand: Kapro Pages: 60

Brand: ATIM Pages: 25

MJK MagFlux Series

Brand: Xylem Pages: 179

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands