AVL 9120 Service Manual Download Page 77 | Manualshive

Page: 77 / 114

background image

6

Adjustments

The 9120, 30, 40, 80 and 81 Analyzers have been designed to require minimal
electronic adjustment. The sample sensor circuit may require adjustment following a

change of the sample sensor or during routine troubleshooting. The temperature
adjustment is active only for models 9140/9180/9181 and requires the temperature
adjustment test plug for correct calibration of the temperature circuit.

6.1 Sample Sensor Adjustment

Select

TEST SAMPLE SENSOR

in the

SERVICE FUNCTIONS

menu

which will display the current sample sensor setting. Adjust R93 Sample Sensor
Adjust located at the top of the ISE SBC card to a value of 100. Press

YES

to

turn on peristaltic pump and ensure displayed value remains constant.

Raise sample door and aspirate clear fluid (e.g. water). Displayed reading should

now be 150 or greater.

Note: R93 can be accessed through the rear cover vent slot and is located at

the top center on the circuit card.

6.2 Temperature Adjustment

(9140/9180/9181 only)

Select

AMPLIFIER TEST

in the

SERVICE FUNCTIONS

menu which will

display the current amplifier voltages. Press

NO

twice to display the temperature

voltage and actual temperature display. Unplug the sample sensor and fit the
Temperature Adjustment Test Plug in place of the sample sensor plug. Adjust R54
located on the SBC Board for a display of 3000mV. Unplug the Temperature

Adjustment Test Plug and fit the sample sensor connector to display the actual
temperature of the measuring chamber.

Due to the elevated temperature inside the analyzer, it is normal for the
displayed temperature to be several degrees C higher than the actual room
temperature.

If no Temperature Adjustment Test Plug is available, place a quality thermometer
(preferably mercury) next to the right side electrode holder. With the front door

open, wait approx. 10 min. Then adjust the displayed temperature to match the
reading on the thermometer.

71

«
...
75
76
77
78
79
...
»

Summary of Contents for 9120



















































































































Reviews:

No comments

Related manuals for 9120

Brand: IFM Pages: 2

Brand: Nagano Keiki Pages: 25

Brand: GARANT Pages: 368

Brand: Oldham Pages: 96

Brand: OHAUS Pages: 71

Brand: PITSID Pages: 22

Brand: Swan Analytical Instruments Pages: 102

Microlog GX Series

Brand: SKF Pages: 342

DUSTHUNTER C200

Brand: SICK Pages: 126

Brand: Ratek Pages: 25

Brand: Young Pages: 5

SiteHawk SK-6000

Brand: BIRD Pages: 69

Brand: Rubicson Pages: 4

Brand: YOSensi Pages: 27

Brand: Scheppach Pages: 20

Brand: HTC Pages: 2

Brand: TDI Pages: 32

Brand: J-TECH Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands