Your ATA Automatic Garage Door
Opener has many features which
you will appreciate. The compo-
nents and materials used in this
Automatic Opener are of the latest
technology and highest quality. Be-
low are listed some of the many fea-
tures.
OPERATION
To operate the door simply press the
hand held transmitter or the wall
mounted transmitter or optional wall
switch for two seconds and the door
will automatically open or close.
The door can be stopped during an
opening or closing cycle by pressing
again. The next actuation will move
the door in the opposite direction.
HOPPING CODE
Every time a transmission is made
from the Remote Transmitter a new
security code is generated. The
n u m b e r o f p o s s i b l e c o d e
combinations is over 4.29 billion.
This greatly enhances security of the
system. Code ‟Grabbing‟ is made a
thing of the past.
ISS (INTELLIGENT SAFETY
OBSTRUCTION SYSTEM)
While the door is doing a closing
cycle and if it should hit an obstacle
or be restricted in some manner, it
will automatically reverse. The
amount of force the door should
encounter before reversing, is
automatically adjusted by the doors
control system, during the initial
installation of the automatic door
opener. The door also if restricted
whilst opening will stop. The Safety
Obstruction Force should be
checked at least once a month. See
installation manual for instructions.
SECURITY CODE STORE
The Opener uses state of the art
technology in storing your selected
Transmitter Security Code. Up to 27
different codes can be stored in the
Openers memory.
OPEN AND CLOSE DRIVE
BUTTONS
Another feature developed by
Automatic Technology Australia in
aiding in the installation of the
opener is the Open and Close Drive
Buttons. These buttons are used to
help set the open and close limit
positions. A quicker setting time
and a more precise limit position
can be achieved using this feature.
INITIALISATION
The Reset button on the Door
Opener is used to initialise or re
-initialise the obstruction settings
and door travel counts. See
installation manual for instructions.
AUTO CLOSE MODE
The Opener can be programmed to
automatically close after an open
cycle. The Auto Close time is
adjustable. It is compulsory to in-
stall a Photo Electric Beam if this
mode is selected, otherwise the door
will not operate.
SAFETY AUTO RUN TIME
If the Opener does not complete its
cycle within thirty seconds the
Opener will stop if opening, and re-
verse back open if closing automati-
cally.
PHOTO ELECTRIC BEAM
(OPTIONAL)
The Opener has an input for a Photo
Electric Beam to be connected for
extra safety protection. And use of
the Auto Close Mode
MANUAL OPERATION
The Opener is equipped with a
unique Manual Disengaging Device.
If the power to the Opener is
disrupted for any reason the door
can be put into Manual Mode by
pulling down on the string handle,
then releasing. This will allow you
to manually open or close the door.
When power is restored, by pulling
down on the string handle and
releasing, the opener is put back into
Automatic Mode.
To store any code simply press and
hold the Door Code button on the
Opener and press the Transmitter
button twice. Each or all codes can be
deleted and changed at any time. The
codes can also be stored with the
Transmitter from a remote location.
OVER LOAD INDICATOR
When the maximum opening and
closing capacity of the Opener is
exceeded the Courtesy Light will
flash 10 times and an audible beeper
will sound to indicate that an Over-
load has occurred.
SERVICE INDICATOR
The Opener has a Service indicator.
When the Overload LED light flashes
and the beeper sounds at the start of a
door cycle, it means that the opener
and or garage door needs a service.
AUTO COURTESY LIGHT
The Courtesy Light on the Opener
comes on automatically whenever the
door is activated to do an opening or
closing cycle. The Light can also be
switched on and off without operat-
ing the door. This is done by pressing
the button on any Hand Held Trans-
mitter or Wall Mounted Transmitter
which has been stored with the light
code, or by pressing the light button
on the Wall Switch (optional). The
light will stay on for approximately
three minutes then switch off. This
time is also adjustable.
CAS (COLOUR ASSISTED
SETTINGS)
To make the installation of the
Automatic Opener more user friendly
Automatic Technology Australia
developed the CAS (Colour Assisted
Settings) system. This unique system
makes installation easy and quick, as
all the Open and Close adjustments
and settings are colour coordinated.
Red for Close and Green for Open. .
FEATURES
3
