background image

PLEASE READ THESE IMPORTANT SAFETY RULES  

Failure to comply with the following Safety Rules may result in  

Serious Personal injury and/or Property Damage

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, Statutory or 
otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Roll Up Garage Door Opener  
and  
Automatic Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered 
by any person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Roll Up Garage Door Opener in accordance 

For 

ADDITIONAL  SAFETY 

protection  we 

STRONGLY 

recommend the fitting of a Photo Electric 

beam. In most countries Photo Electric Beams are man-
datory on all garage doors fitted with Automatic Open-
ers. For a small additional outlay ATA recommends that 
Photo  Electric  Beams  be  installed  with  the  Automatic 
Opener insuring additional safety and peace of mind. 
 

 

 

DO  NOT 

operate  the  Garage  Door  Opener  unless  the 

Garage Door is in full view and free from objects such 
as  cars  and  children/people. 

SERIOUS  PERSONAL 

INJURY

  and/or  property  damage  can  result  from  fail-

ure to follow this warning.  
 

DO  NOT 

operate the Garage Door Opener when chil-

dren/persons are near the door. Children must be super-
vised  near  garage  door  at  all  time  and  when  Door 
Opener  is  in  use.

  SERIOUS  PERSONAL  INJURY 

and/or property damage can result from failure to follow 
the warning. 
 

DO  NOT 

allow  children  to  operate  the  Garage  Door 

Opener. 

SERIOUS  PERSONAL  INJURY 

and/or 

property  damage  can  result  from  failure  to  follow  this 
warning. 
 
Make  sure  that  the 

SAFETY  OBSTRUCTION 

FORCE 

is working correctly, and is 

TESTED

 and set 

as  per  the  Installation  Instructions  Manual.  Failure  to 
follow  the  Manual  could  result  in 

SERIOUS  PER-

SONAL  INJURY 

and/or  property  damage.  This  test 

must be  repeated at  regular intervals and the  necessary 
adjustments made if required. 
 

DO  NOT 

disengage the Door Opener to manual opera-

tion with children/persons or any other objects including 
motor vehicle within the doorway. 
 
Install the wall switch or wall mounted transmitter in a 

LOCATION  /  POSITION 

where  the  garage  door  is 

visible and out of reach of  children. 

The  Garage  door  must  be 

WELL  BALANCED

Sticking or binding doors must be repaired by a quali-
fied garage door installer prior to Opener installation. 
 

DO  NOT 

attempt to repair door yourself as hardware 

is  under  extreme  tension  and  can  cause 

SERIOUS 

PERSONAL INJURY 

and/or property damage. 

 

REMOVE  OR  DISENGAGE 

all garage doors locks 

and mechanisms prior to installation of Opener. 
 
Connect  the  Garage  Door  Opener  to  a  properly 

EARTHED

  general  purpose  240V  outlet installed by 

a qualified electrical contractor. 
 

DISCONNECT  THE  POWER  CORD 

from  main 

power before making any repairs or removing covers. 
Only 

EXPERIENCED 

service personnel can remove 

covers from Opener. 
 
Keep  hands  and  loose  clothing 

CLEAR

  of  the  door 

and Door Opener at all times. 
 
When using auto close mode a 

PHOTO  ELECTRIC 

BEAM 

 must be fitted correctly and tested for opera-

tion  at  regular  intervals. 

EXTREME  CAUTION 

is 

recommend  when  using  auto  close  mode.  All 

SAFETY

 

RULES

 above must be followed. 

 
In order for the Garage Door Opener to 

SENSE

 an ob-

ject obstructing the door way, some 

FORCE

 must be 

exerted on the object. As a result the object, door and/
or person may suffer 

DAMAGE or INJURY .  

 

Make  sure  that  the  door  is  fully  open  before  driving 
into or out of the garage. 
 
Make  sure  the  door  is  fully  closed  before  leaving  the 
driveway.  
   

Summary of Contents for ROLL UP GARAGE DOOR OPENER





















Reviews: