manualshive.com logo in svg

Automated Logic RC642, Technical Instructions

Share
Download
Automated Logic RC642 Technical Instructions Download Page 7

 

 

3 

   

 

BACnet support 

Conforms to the Advanced Application Controller (B-AAC) 

Standard Device Profile as defined in ANSI/ASHRAE 

Standard 135-2004 (BACnet) Annex L  

Listed by 

UL-916 (PAZX), cUL-916 (PAZX7), FCC Part 15-Subpart B-

Class A, CE EN50082-1997 

  
 

 

 

The Room Controller has 4 inputs that accept the signal types described below. 

  

These 

inputs...

 

Support this 

signal type...

 

  

Description 

All inputs 

Thermistor 

Precon type 2 (10 kOhm at 77°F). Input voltages should 

be from 0.489 Vdc to 3.825 Vdc for thermistors. 

All inputs 

Dry contact 

A 5 Vdc wetting voltage detects contact position, 

resulting in a 0.5 mA maximum sense current when the 

contacts are closed. 

Input 3 

Input 4 

0–5 Vdc 

The output impedance of a 0–5 Vdc source must not 

exceed 10 kOhms. The input impedance of the Room 

Controller is approximately 1 MOhm. 

All inputs 

Pulse counter*  Pulse counting up to 10 pulses per second.  

Minimum pulse width (on or off time) required for each 

pulse is 50 msec. 

All inputs 

Timed local 

override 

A momentary contact switch that overrides a schedule 

and turns equipment on for a defined period of time. The 

override time added for each push of the button and the 

maximum allowable On time are software adjustable. 

*

  

The Room Controller can perform pulse counting for dry contact or voltage inputs if you assign 

the input to a Pulse to Analog Input microblock. See 

To assign inputs or outputs to points

 (page 

17).

 

  

NOTE

  The Room Controller has a built-in room temperature sensor (Input 6) that is read 

by an RS Zone Sensor microblock. You must use a BACview to calibrate the temperature 

sensor in a stand-alone Room Controller. See:  

Appendix C - 

Editing properties in a built-in control program

 (page 86) 

Creating a custom control program

 (page 6) 

  
 

 

The Room Controller has 6 digital outputs. These outputs are small pilot relays that drive 

external 24 Vac relays/devices (or 26 Vdc, depending on the controller's power supply). 

Each output is a wet contact rated at 1 A maximum and is normally open. 
  
 

 

The Room Controller has 2 analog outputs that support voltage devices from 0-10 Vdc. 

The controlled device must have a minimum of 1000 Ohms resistance measured from its 

input to ground and must share the same ground as the controller. 

 

Inputs 

Digital outputs 

Analog outputs 

Summary of Contents for RC642































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands