Please state device type and our order number (see name plate) when ordering spare parts. Only original AUMA spare parts should be used.
Failure to use original spare parts voids the warranty and exempts AUMA from any liability. Representation of spare parts may slightly vary
from actual delivery.
Type
Designation
Ref. no.
Type
Designation
Ref. no.
Sub-assembly
Output drive type B3/E/B4
549.0
Sub-assembly
Bearing flange
002.0
Sub-assembly
Output drive sleeve B3/E/B4
549.1
Sub-assembly
Former hollow shaft (for bearing bush
600.0)
003.0
Parallel key
551.1
Sub-assembly
New hollow shaft (for ball bearing 635.0)
003.0
Mechanical position indicator
553.0
Drive shaft
005.0
Sub-assembly
Potentiometer as position transmitter
556.0
Motor coupling
005.1
Sub-assembly
Potentiometer without slip clutch
556.1
Sub-assembly
Coupling pin
005.2
Heater
557.0
Manual drive coupling
005.3
Sub-assembly
Blinker transmitter including pins at wires
(without impulse disc and insulation plate)
558.0
Sub-assembly
Pull rope
005.4
Sub-assembly
Electromechanical control unit with
switches, including torque switching heads
559.0
Worm wheel
006.0
Sub-assembly
Position transmitter RWG
566.0
Sub-assembly
Manual gearing
009.0
Sub-assembly
Potentiometer for RWG without slip clutch
566.1
Sub-assembly
Torque lever
017.0
Sub-assembly
Position transmitter board for RWG
566.2
Sub-assembly
Gear segment
018.0
Sub-assembly
Cable set for RWG
566.3
Crown wheel
019.0
Slip clutch for potentiometer
567.1
Swing lever
020.0
Stem protection tube (without cap)
568.1
Drive pinion II for torque switching
022.0
Sub-assembly
Protective cap for stem protection tube
568.2
Sub-assembly
Output drive wheel for limit switching
023.0
Sub-assembly
V-seal
568.3
Sub-assembly
Drive wheel for limit switching
024.0
Threaded sleeve (for SAEx/SAREx 25.1
and 30.1)
568.4
Sub-assembly
Locking plate
025.0
Sub-assembly
Change-over lever assy
569.0
Sub-assembly
Wire for protective earth
058.0
Sub-assembly
Change-over lever
569.1
Sub-assembly
Motor
070.0
Sub-assembly
Notched pin
569.2
Sub-assembly
Planetary gearing for motor drive (for
ADX.90 motor)
080.0
Sub-assembly
Stem nut (without thread)
575.1
Sub-assembly
Reduction gearing
155.0
Sub-assembly
Switch for limit/torque
579.0
Sub-assembly
Cover
500.0
Spacer
580.1
Sub-assembly
Threaded plug
511.0
Stud bolts for switches
581.0
Output drive type A (without stem nut)
514.0
Bearing bush (for former hollow shaft)
600.0
Axial needle roller bearing
514.1
Motor connection
603.0
Radial seal for output drive type A
514.2
Frame for electrical connection
605.0
Sub-assembly
Terminal frame (without terminals)
528.0
Cover
607.0
Sub-assembly
End clamp
529.0
Shim washer (for new hollow shaft)
634.0
Sub-assembly
Terminals for motor/controls
533.0
Ball bearing (for new hollow shaft)
635.0
Sub-assembly
Snap ring
535.1
Set
Seal kit, small
S1
Sub-assembly
Screw plug
539.0
Set
Seal kit, large
S2
Protective earthing
541.0
Sub-assembly
Handwheel with ball handle
542.0
99
SAEx 25.1 – SAEx 40.1 / SAREx 25.1 – SAREx 30.1
ACExC 01.2
Spare parts
