Audio Note DAC Kit 3.1 Page 44 Instruction Manual Download | Manualshive

Page: 44 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 44

Installing the LED Indicator

The LED on the M2 Power Supply
Board will be the first indicator that we
have power

– I would suggest just

taping the LED

– make sure the metal

leads of the LED are not touching any
other circuitry or chassis

– Note the

Led has not been pushed in all the
way.

Also note that the LED will only work
when inserted the correct way around.

Installing the tubes

Let‟s install our tubes into the board – the supplied 6X5 in
the 8-pin valve base and the ECL82 (or 6BM8) in the 9-pin
base.

Tidying Up

Seeing as we have a number of loose filament and HT
wires coming from the PCB, I would suggest taping the
ends to make sure that they do not short with one another
when we go to test with power!

«
...
42
43
44
45
46
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: NAD Pages: 10

Brand: GADGETMONSTER Pages: 26

Brand: Chemtronics Pages: 20

Brand: EtherWAN Pages: 13

Brand: EINHELL Pages: 10

Brand: Inorea Pages: 104

Evolute RTLA50-S

Brand: Renishaw Pages: 11

Brand: Costway Pages: 25

Brand: Varan Pages: 27

Brand: Kramer Pages: 15

10/100/1000 (SFP)

Brand: Dynamix Pages: 2

Brand: TRUELOOK Pages: 12

IFS MC250-4T Series

Brand: Interlogix Pages: 23

Brand: Xantrex Pages: 124

Digi Edgeport/1i

Brand: Inside Out Networks Pages: 22

LOUDSPEAKER SP100

Brand: Sonos Pages: 46

Delphi E48SR05012NRFA

Brand: Delta Electronics Pages: 15

Integrated Multi-Application Generator

Brand: Telrad Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands