Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 31 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 31

Now take the short wire from BAG #2 - we will be using this
to hardwire from the 8-pin valve base to the 9-pin valve
base.

The graphic to the left shows the
connections for the twisted wires.

EXPLANATION

: On the M2 Power

Supply  Board  we  will  have  2
different  tubes  -  a  6X5  and  an
ECL82.  As  explained  before,  in
order for tubes to operate they need
a  filament  voltage  -  we  will  be
supplying  6.3V  AC  to  both  of  these
tubes.  The  wire  we  are  installing
here  is  used  to  “parallel”  the  6.3V
AC  that  will  be  coming  from  the
secondary of the Mains transformer.

Note in these pictures the twisted wire
has  been  soldered  into  pins  4  &  5  on
the 9-pin valve base.

On  the  9-pin  valve  base  note  the
upper  and  lower  holes  through  the
pins.  Connect  the  current  red  &  black
wires  to  the

lower

hole on the valve

pin.

«
...
29
30
31
32
33
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: Panasonic Pages: 38

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 174

Brand: Struck Pages: 79

OmniConverter GPoE+/S

Brand: OST Pages: 10

Brand: Kohler Pages: 44

Brand: Nitek Pages: 2

Brand: Potek Pages: 18

Brand: Mystery Pages: 36

Brand: Viking Pages: 4

Brand: e+p Elektrik Handels Pages: 2

Brand: KAMEHA Pages: 12

Brand: Lika Pages: 2

Brand: Nightlife Pages: 12

Brand: Casti Pages: 4

Brand: Missing Link Pages: 8

Brand: MAER IDROPULITRICI Pages: 48

Q.HOME+ ESS HYB-G2

Brand: Q CELLS Pages: 60

Brand: CEL-MAR Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands