Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 52 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 52

Board Installation and Wiring

Position the Digital Power Supply board into the chassis as
shown with the DC voltage side (AGND DGND etc.)
positioned away from the Power Supply.

BE SURE THAT THE KIT IS NOT PLUGGED INTO THE WALL at this point.

Take the prepared twisted blue wire and locate the 9-0-9 taps on the Mains transformer secondary. Then strip, and tin the
blue wire and solder to the 9 & 9 taps

– These blue wires then come around the transformer and connect into the AC pads

on the power supply board.

Take a black wire and connect the 0 tap from the Mains transformer to the CT pad on the digital power supply board.

«
...
50
51
52
53
54
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: YASKAWA Pages: 128

Brand: IDK Pages: 44

Brand: S.M.S.L Pages: 31

Solar station S

Brand: meibes Pages: 21

Brand: PanelClaw Pages: 19

Brand: National Semiconductor Pages: 13

Brand: Datavideo Pages: 13

Brand: T+A Pages: 64

Brand: LogicLadder Pages: 55

Brand: Raritan Pages: 20

Brand: MULTIQUIP Pages: 62

Brand: Nyrius Pages: 11

Brand: V-TAC Pages: 21

Brand: l-com Pages: 11

Prizm 200750 Series

Brand: Moog Pages: 12

Brand: Tektronix Pages: 188

Brand: Tripp Lite Pages: 4

Brand: Data Connect Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands