manualshive.com logo in svg

Audio Note DAC Kit 3.1, Instruction Manual

The Audio Note DAC Kit 3.1 is a high-quality audio digital-to-analog converter. Unlock its full potential by referring to the comprehensive Instruction Manual. Download the manual for free from our website manualshive.com, and delve into precise installation, setup, and usage instructions to enhance your audio experience.

Share
Download
background image

Copyright © 2006-2011 AudioNote Kits 

www.AudioNoteKits.com

 

[email protected]

  

 

Page 2 

 

Table of Contents 

 
Section1: Introduction ............................................................................................................................................................ 4

 

Overview ............................................................................................................................................................................ 5

 

Component Placement Breakdown .................................................................................................................................... 6

 

Electrical Safety Warning ................................................................................................................................................... 8

 

Section 2: Mechanical Assembly ........................................................................................................................................... 9

 

Installing the feet ................................................................................................................................................................ 9

 

Mains Transformer, Choke, and Mains Installation ............................................................................................................ 9

 

Configuring the Primary Winding for your World Region .............................................................................................. 11

 

Installing the IEC Socket (AC Socket) and Rocker Switch ........................................................................................... 14

 

Installing the Choke ...................................................................................................................................................... 15

 

Installing the Mains Transformer .................................................................................................................................. 15

 

Wiring up the Mains ...................................................................................................................................................... 16

 

Shield Positioning ......................................................................................................................................................... 17

 

Section 3: M2 Power Supply ................................................................................................................................................ 19

 

M2 Power Supply Board Parts List .................................................................................................................................. 20

 

M2 Power Supply Board Construction Steps ................................................................................................................... 21

 

Installing the Valve Bases ............................................................................................................................................ 21

 

Installing the Resistors ................................................................................................................................................. 23

 

Installing resistors in the HT ADJUST position ............................................................................................................. 25

 

Zener Diode Installation ................................................................................................................................................ 26

 

Electrolytic Capacitor Installation .................................................................................................................................. 27

 

Installing the Bridge Rectifier ........................................................................................................................................ 29

 

Installing the Non-Polarized Capacitors........................................................................................................................ 29

 

Wiring the M2 Power Supply Board .............................................................................................................................. 30

 

Filament Component Section of the M2 Power Supply Board ...................................................................................... 33

 

Regulator Installation .................................................................................................................................................... 34

 

Installing the LED Harness ........................................................................................................................................... 35

 

Remaining Wire Connections ....................................................................................................................................... 35

 

Installing the Heatsink .................................................................................................................................................. 36

 

Installing the Choke Wire .............................................................................................................................................. 37

 

Inter-wiring to the Mains Transformer ........................................................................................................................... 38

 

Securing the Regulators to the Heatsink ...................................................................................................................... 41

 

Section 4: M2 Power Supply Testing ................................................................................................................................... 43

 

Preparations ..................................................................................................................................................................... 43

 

Fitting the Mains Fuse .................................................................................................................................................. 43

 

Installing the LED Indicator ........................................................................................................................................... 44

 

Installing the tubes ........................................................................................................................................................ 44

 

Tidying Up .................................................................................................................................................................... 44

 

Ohm Check ...................................................................................................................................................................... 45

 

Electrical Testing .............................................................................................................................................................. 45

 

Voltage Check Summary ................................................................................................................................................. 47

 

DC Voltage Checks ...................................................................................................................................................... 47

 

AC Voltage Checks ...................................................................................................................................................... 47

 

Section 5: Digital Power Supply PCB .................................................................................................................................. 48

 

Parts List .......................................................................................................................................................................... 48

 

Construction ..................................................................................................................................................................... 48

 

Installing the LED‟s ....................................................................................................................................................... 49

 

Installing the Capacitors ............................................................................................................................................... 49

 

Installing the Diodes ..................................................................................................................................................... 50

 

Installing the Resistors ................................................................................................................................................. 51

 

Board Installation and Wiring ........................................................................................................................................... 52

 

Section 6: Install the Screen ................................................................................................................................................ 54

 

Section 7: Installing the Digital PCB .................................................................................................................................... 55

 

Digital Board Overview ..................................................................................................................................................... 55

 

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

La Marche FT Series Installation And Operation Manual preview
FT Series
Brand: La Marche Pages: 18
Panduit Atlona Omega AT-OME-SR21 Manual preview
Atlona Omega AT-OME-SR21
Brand: Panduit Pages: 28
APS FC205 Operation Manual preview
FC205
Brand: APS Pages: 70
Viking PF--6A Technical Practice preview
PF--6A
Brand: Viking Pages: 4
meibes Solar station S Technical Information For Installation And Operation preview
Solar station S
Brand: meibes Pages: 21
PanelClaw Polar Bear III Installation Manual preview
Polar Bear III
Brand: PanelClaw Pages: 19
Sime NATURAL 300/8.16 S Installation And Servicing Instruction preview
NATURAL 300/8.16 S
Brand: Sime Pages: 56
Balluff BNI00C1 Installation Manual preview
BNI00C1
Brand: Balluff Pages: 2
Speaka Professional P-UCFS-01 Operating Instructions Manual preview
P-UCFS-01
Brand: Speaka Professional Pages: 8
CYP AU-11SA-4K22 Operation Manual preview
AU-11SA-4K22
Brand: CYP Pages: 9
Tripp Lite PowerVerter Plus PV 1000FC Owner'S Manual preview
PowerVerter Plus PV 1000FC
Brand: Tripp Lite Pages: 20
KEB COMBIVERT F4-S Series Instruction Manual preview
COMBIVERT F4-S Series
Brand: KEB Pages: 30
Mikroe Click Board ADC 3 click Quick Start Manual preview
Click Board ADC 3 click
Brand: Mikroe Pages: 2
TechNexion Vizionlink PCIE-VL-3120 Quick Install Manual preview
Vizionlink PCIE-VL-3120
Brand: TechNexion Pages: 2
Elenco Electronics GF-8056 User Manual preview
GF-8056
Brand: Elenco Electronics Pages: 12
2N 918620E Brief Manual preview
918620E
Brand: 2N Pages: 17
SMA SUNNY BOY STORAGE 3.7 Operating Manual preview
SUNNY BOY STORAGE 3.7
Brand: SMA Pages: 142
Tesla MediaBox X300 Manual preview
MediaBox X300
Brand: Tesla Pages: 19

Brands by name

Popular brands

Load more brands