Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 13 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 13

Now we must configure our Mains transformer for the World Voltage that we reside in.

For this example we will show

120V Operation

.

Start by cutting two short pieces of
wire approx 2” in length each, stripping
the insulation off the ends and tinning
the wire.

Then we will inter-wire the Mains transformer primaries.

Remember, we are wiring here for 120v - if your region is
different then you will need to consult the wiring chart on
the previous page to determine how you inter-wire for your
region.

From  the  IEC  bag  we  want  to  take  the  brown  and  blue
wires with the crimps on one end.

Trim  the  wires  to  about  _____  inches  in  length  and  then
solder on to the correct Mains transformer primary tags for
your region.

«
...
11
12
13
14
15
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: ZCS Pages: 74

Brand: Planet Pages: 7

Brand: Engel Pages: 42

HUBNER BERLIN POG 10 + DSL

Brand: Baumer Pages: 36

Brand: NEXENTRO Pages: 8

S-1000MM-M2xx05

Brand: Perle Pages: 12

CSI 23KTL-CT/US-480

Brand: CanadianSolar Pages: 88

Brand: Black Box Pages: 20

Y/C to NTSC Conversion PCN-40

Brand: Link Pages: 2

Brand: Wirez Pages: 16

EASI ATM IND2x2 Series

Brand: Teleste Pages: 28

Frenic Mini FRN001C1E-2U

Brand: Fuji Electric Pages: 196

Brand: Sunforce Pages: 1

climatronic converter WMS UP

Brand: WAREMA Pages: 4

NX Distributed Intelligence NX MEDIA CONVERTER

Brand: Hubbell Pages: 3

Brand: Drivecon Pages: 28

Brand: Solax Pages: 3

Brand: Hagstrom Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands