Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 43 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 43

Section 4: M2 Power Supply Testing

Preparations

Fitting the Mains Fuse

In  this  section  we  are  going  to
electrically test the power supply.

Start  by  installing  a  1A  Slo  Blo  fuse
(IEC BAG) into position as shown.

Use a screwdriver or flat edge or your
fingers  pull  the Fuse  holder  out   -  you
will  need  to  squeeze  to  completely
remove it.

Insert the fuse into the holder as
shown opposite.

With the fuse installed into the holder
insert back into the IEC plug.

With the Fuse installed we are ready
to do some testing!

READ the entire remaining section first
before taking any actions!

«
...
41
42
43
44
45
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: Samson Pages: 40

SignalPilot 51840

Brand: Esu Pages: 32

Brand: Milexia Pages: 17

Brand: AVT Pages: 82

Brand: Trace Engineering Pages: 2

Brand: AV Link Pages: 2

Brand: Metra Electronics Pages: 9

Brand: FBS Pages: 6

Brand: KONANlabs Pages: 6

Brand: mundoclima Pages: 60

Brand: Lindy Pages: 14

Brand: Badger Power Electronics Pages: 29

Brand: Esu Pages: 8

Brand: AGM Pages: 71

Brand: V-TAC Pages: 100

Brand: Mede8er Pages: 21

Brand: Kramer Pages: 12

Brand: LDA Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands